Thermo-mechanical high-cycle fatigue analysis of exhaust manifold of turbocharged engine with two-way coupling FSI
نویسنده
چکیده مقاله:
NNowadays, car manufactures in order to increasing torque and power with consider to fuel consumption, have swept to production of turbocharged engines. With consider to exhaust gas-temperature rises in boosted engines, recognition of critical locations of exhaust manifold in the worse condition of engine (full load and maximum speed), to prevent fracture of exhaust manifold is very important. In this research thermomechanical analysis, fatigue and life-span estimation in the most critical case of engine performance with using two-way coupling of fluid and solid has been carried out. In two-way coupling in every time step first, flow analysis of manifold is carried out in FLUENT software, then, temperature, convective heat transfer coefficient and pressure of fluid are mapped to inner shell of exhaust manifold. In solid preload of bolts, elastic foundation based for effect of cylinder head and turbocharger were considered and thermomechanical analysis was carried out with ANSYS software. Then with computing strain and changing geometry, new mesh for analysis in next time step was entered into FLUENT software and this cycle with consider to time step until end of cycle was carried out. Results of thermal simulation in fluid and solid was validated with experimental data. Finally, temperature, heat transfer coefficient, solid temperature, strain, normal stresses, Von Misses stress and dynamic stress plot and life-span of exhaust manifold have been estimated.
منابع مشابه
Detection of Exhaust Manifold Leaks on a Turbocharged SI-engine with Wastegate
Emissions from modern SI-engines are reduced by a three way catalyst. However if there are leaks in the exhaust system before the catalyst emissions increase for two reasons. First the untreated emissions leak out. Second which is worse, due to waves in the exhaust system, oxygen leaks into the manifold and causes an oxygen sensor offset. The result is increased emissions as the air/fuel contro...
متن کاملEvaluation of Thermal Barrier Coating in Low Cycle Fatigue Life for Exhaust Manifold
This paper presents low cycle fatigue (LCF) life prediction of a coated and uncoated exhaust manifolds. First Solidworks software was used to model the exhaust manifolds. A thermal barrier coating system was applied on the tubes c of the exhaust manifolds, consists of two-layer systems: a ceramic top coat (TC), made of yttria stabilized zirconia (YSZ), ZrO2-8%Y2O3 and also a metallic bond coat ...
متن کاملLocation Isolability of Intake and Exhaust Manifold Leaks in a Turbocharged Diesel Engine with Exhaust Gas Recirculation
An investigation into the isolability of the location of intake and exhaust manifold leaks in heavy duty diesel engines is presented. In particular, established fault detection and isolation (FDI) methods are explored to assess their utility in successfully determining the location of a leak within the air path of an engine equipped with exhaust gas recirculation and an asymmetric twin-scroll t...
متن کاملExhaust Manifold Pressure Estimation on a Turbocharged Si-engine with Wastegate
In turbocharged engines with wastegate the exhaust pressure can change rapidly. A method to estimate the exhaust manifold pressure is presented for diagnosis of wastegate and turbocharger on spark-ignited engines. It does not require any extra sensors in the exhaust system after the calibration. A non-linear model is developed of the exhaust pressure. Estimates of the exhaust manifold pressure ...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 60 شماره 60
صفحات 0- 0
تاریخ انتشار 2020-12
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
کلمات کلیدی برای این مقاله ارائه نشده است
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023