Pilot in-Situ Production of AL-TiB2 and AL-ZrB2 Composites Using Reactive Slag
نویسنده
چکیده مقاله:
In this research work, the possibility of semi industrial production of Al-TiB2 and Al-ZrB2 composites, using reactive slag in a flame furnace have been investigated. For this purpose, commercial pure aluminum and powder mixture of TiO2 (ZrO2) , KBF4 and Na3AlF6 were used. The results showed that using a proper ratio of slag forming materials as well as proper amounts of the above-mentioned compounds make it possible to produce good quality Al-TiB2 and Al-ZrB2 compounds employing the conventional melting equipment such as a flame furnace.
منابع مشابه
IN-SITU FABRICATION PROCESS OF AL- TIC COMPOSITE BY SLAG
The new in situ method for AI-TiC composite fabrication has been carried out. In this method, fabrication of AI-TiC composite by simultaneous introduction of titanium oxide and carbon into aluminum melt was investigated.. Under the process conditions, titanium and carbon reaction results in titanium carbide whiskers. The salt containing keriolite (Na3AIF6), titanium oxide (TiO2) and graphite us...
متن کاملMicrostructure Evolution and Mechanical Properties of Al-TiB2/TiC In Situ Aluminum-Based Composites during Accumulative Roll Bonding (ARB) Process
In this study, a kind of Al-TiB₂/TiC in situ composite was successfully prepared using the melt reaction method and the accumulative roll-bonding (ARB) technique. The microstructure evolution of the composites with different deformation treatments was characterized using field emission scanning electron microscopy (FESEM) and a transmission electron microscope (TEM). The mechanical properties o...
متن کاملProduction and microstructural investigation of Al-nano TiB2 composite produced by powder metallurgy technique
Automotive and aerospace industries are required to light materials which have high properties. This causes to reduce production cost and fuel consumption. One of these advanced materials that have been attracted at these decades is particulate metal matrix nanocomposites. These materials have a combination of ductile matrix alloy properties and ceramic reinforcement nanoparticles. Powder metal...
متن کاملRefining Mechanism of 7075 Al Alloy by In-Situ TiB2 Particles
The nucleation undercooling of TiB₂/7075 Al matrix composites, the microstructure observed after solidification at different cooling rate, and the size and distribution of TiB₂ particles were investigated. The experimental results have shown that the grain sizes of TiB₂/7075 Al matrix composites firstly decreased, then increased, and finally decreased again with the increase of TiB₂ content. Th...
متن کاملFabrication of TiCx-TiB2/Al Composites for Application as a Heat Sink
Metal matrix composites reinforced with ceramic particles have become the most attractive material in the research and development of new materials for thermal management applications. In this work, 40-60 vol. % TiCx-TiB₂/Al composites were successfully fabricated by the method of combustion synthesis and hot press consolidation in an Al-Ti-B₄C system. The effect of the TiCx-TiB₂ content on the...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 23 شماره 1
صفحات 179- 188
تاریخ انتشار 2004-07
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023