Occupational exposure to welding gases during three welding processes and risk assessment by SQRCA method
نویسندگان
چکیده مقاله:
Background: Hazardous chemical agents in the welding operation are a mixture of metal fumes and toxic gases, the inhalation of which causes adverse health effects among welders. The emission of gases in the workplace is a logical cause for concern regarding the potential development of respiratory disease. The aim of the present study was to determine the concentration values of gases discharged during arc welding and perform risk assessment through semi-quantitative chemical risk assessment ‎(SQCRA) method. Materials and Methods: This cross-sectional study was conducted in an Iranian steel mill on the 3 processes of plasma arc welding (PAW), submerged arc welding (SAW), and gas tungsten arc welding (GTAW). Direct reading instruments were used for sampling of carbon dioxide (CO2), carbon monoxide (CO), nitrogen monoxide (NO), nitrogen dioxide (NO2), and ozone (O3). SQCRA method was used for risk assessment of gases. Results: The concentrations of O3 (0.356 ppm), CO (41.642 ppm), NO (6.357 ppm), and NO2 (4.871 ppm) were found to exceed their threshold limit values (TLVs), while the concentrations of CO2 (3879.285 ppm) were below its TLV. The maximum exposure concentration of all gases, except CO2, was observed in SAW. SQCRA method showed that among the gases, the highest and least risk rating was related to ozone and nitrogen monoxide, respectively. The risk rating for CO2, CO, and NO2 was low, high, and very high, respectively. Conclusions: In this study, exposure values were higher than the threshold limit values-time weighted average (TLV-TWA) and the results of risk assessment showed that control engineering should be applied and the use of respiratory protective equipment (RPE) should be made mandatory for welders especially in SAW, PAW, and GTAW processes.
منابع مشابه
risk assessment of exposure to gases released by welding processes in iranian natural gas transmission pipelines industry
exposure to welding gases can cause health adverse effects. risk assessment is a useful tool for good assessment of exposed workers. the purpose of this study was to determine the risk levels for exposed welders to welding gases. welders (n=239) were selected from iranian natural gas transmission pipelines industry from four regions in iran including assaluyeh, omidieh, loshan, and borujen. ozo...
متن کاملConcentration Evaluation and Health Risk Assessment of Welders' Exposure to Total Fumes and Manganese during Welding at Metal Industry
Introduction and purpose: Risk assessment of toxic or hazardous chemicals enables industrial hygienists to make appropriate decisions regarding management provisions in a healthy workplace. Exposure to total fumes and manganese during welding can have harmful effects on welders’ health. Therefore, the present study was conducted in the metal industry to evaluate the concentration and determine ...
متن کاملoccupational exposure to welding fumes using different ventilation scenarios
welders may suffer from welding fumes generated during the process if the ventilation systems are improperly applied. the objective of the present work was to study the mitigation of air pollutants at welding stations, using different ventilation scenarios. four air pollutants including iron oxide, respirable dust, ozone, and carbon monoxide were measured during four different ventilation scena...
متن کاملOccupational asthma caused by aluminium welding.
Work-related asthma has been documented in workers employed in the primary aluminium industry and in the production of aluminium salts. The role of aluminium in the development of occupational asthma has, however, never been convincingly substantiated. We investigated a subject who experienced asthmatic reactions related to manual metal arc welding on aluminium. Challenge exposure to aluminium ...
متن کاملOccupational exposure to dioxins by thermal oxygen cutting, welding, and soldering of metals.
This paper focuses on one aspect of occupational dioxin exposure that is novel and unexpected. Exposures in excess of the German threshold limit value of 50 pg international toxicity equivalent (I-TEQ)/m3 are very frequent, unpredictable, and sometimes very high--up to 6612 pg I-TEQ/m3--during thermal oxygen cutting at scrap metal and demolition sites. The same procedure involving virgin steel ...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 6 شماره 3
صفحات 144- 149
تاریخ انتشار 2017-07
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023