Numerical Analysis of Stress Distribution During Tunneling in Clay Stone Rock
نویسندگان
چکیده مقاله:
Modern technology has been used to build tunnels in recent years by means of drilling machines (TBM) that were used for civil engineering work in large cities to reduce the harmful effects of spending on the surface of the earth significantly. To build the tunnel, numerical modeling was used on the basis of the finite element method to predict stress behavior during the tunnel construction process. Tunnel simulation model by using the numerical method (FEM) with the Hoek-Brown model, which includes calculating the behavior of predicting stress-that surrounds the tunnel and analysis during the process of building the tunnel and compared with the natural state of the rocks during the different tunnel construction stages. Vertical stresses at the top and bottom of the tunnel are reduced during the advance of tunneling while horizontal stresses are increased. TBM progression is reflected in phases through one to five by performing an axial symmetric FE analysis, math calculation results revealed significant stress changes occurring in rock regions near the boundary of the tunnel. In other words, proximity to rocks is mostly affected by the tunnel. These pressure variations decrease as you move away from the tunnel horizontally and the seams reach extremely small values for distances greater than (2D) meters from the edge of the tunnel, where D is the diameter of tunnel.
منابع مشابه
Sensitivity Analysis of Stress and Cracking in Rock Mass Blasting using Numerical Modelling
Drilling and blasting have numerous applications in the civil and mining engineering. Due to the two major components of rock masses, namely the intact rock matrix and the discontinuities, their behavior is a complicated process to be analyzed. The purpose of this work is to investigate the effects of the geomechanical and geometrical parameters of rock and discontinuities on the rock mass blas...
متن کاملClay-shoveler's fracture during indoor rock climbing.
Indoor rock climbing is becoming more popular for people of all ages. Despite the tremendous interest in this competitive sport, participants are made aware of the dangers associated with participating. The authors present the first reported case of a clay-shoveler's fracture at the T1 spinous process during indoor rock climbing. They describe the management and natural history of this fracture...
متن کاملanalysis of power in the network society
اندیشمندان و صاحب نظران علوم اجتماعی بر این باورند که مرحله تازه ای در تاریخ جوامع بشری اغاز شده است. ویژگیهای این جامعه نو را می توان پدیده هایی از جمله اقتصاد اطلاعاتی جهانی ، هندسه متغیر شبکه ای، فرهنگ مجاز واقعی ، توسعه حیرت انگیز فناوری های دیجیتال، خدمات پیوسته و نیز فشردگی زمان و مکان برشمرد. از سوی دیگر قدرت به عنوان موضوع اصلی علم سیاست جایگاه مهمی در روابط انسانی دارد، قدرت و بازتولید...
15 صفحه اولNumerical Modelling of Backfill Grouting Approaches in EPB Tunneling
One of the main issues involved during tunnel construction with tunnel boring machines is the tail gap grouting. This gap is between the external diameter of tunnel lining and the excavation boundary that is filled with high-pressure grouting materials. In this work, three different approaches of gap grouting modeling in the FLAC3D software are investigated with a special attention to the...
متن کاملApplicability of Elastic Analysis for Predicting the Settlement Distribution Around Tunneling in Soft Ground (TECHNICAL NOTE)
In this article a brief review of the literature on the subject is cited. The method of analysis by a finite element program is discussed in which the effect of different influential parameters are examined. The results of these computations are then compared to the corresponding empirical data and two other existing formulae for two dimensional cases. The comparisons show quite reliable and ac...
متن کاملNumerical investigation of strain distribution during cyclic expansion extrusion (CEE)
Strain distribution of Al 1100 was numerically investigated during cyclic expansion extrusion (CEE) process using finite element method (FEM). Die angle, corner fillet radius and die chamber diameter were considered as die parameters and friction factor and number of passes as process parameters. The effects of these parameters were investigated on the effective strain and strain homogeneity in...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 33 شماره 8
صفحات 1472- 1478
تاریخ انتشار 2020-08-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
کلمات کلیدی
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023