Multi-Objective Optimization of Tio2-Water Nanofluid Flow in Tubes Fitted With Multiple Twisted Tape Inserts in Different Arrangement

نویسندگان

  • H. Safikhani Department of Mechanical Engineering, Faculty of Engineering, Arak University, Arak 38156-88349,Iran
  • S. Eiamsa-ard Department of Mechanical Engineering, Faculty of Engineering, Mahanakorn University of Technology, Bangkok 10530, Thailand
چکیده مقاله:

In this paper, experimentally derived correlations of heat transfer and pressure drop are used in a Pareto based Multi-Objective Optimization (MOO) approach to find the best possible combinations of heat transfer and pressure drop of TiO2-water nanofluid flow in tubes fitted with multiple twisted tape inserts in different arrangement. In this study there are four independent design variables: the number and arrangement of twisted tape inserts (N), TiO2 volume fraction (φ), Reynolds number (Re) and Prandtl number (Pr). Seven twisted tape arrangement in three different categories are investigated. The objectives are maximizing the non-dimensional heat transfer coefficient (Nu) and minimizing the non-dimensional pressure drop (f Re). It is shown that some interesting and important relationships as useful optimal design principles involved in the thermal performance of nanofluid flow in tubes fitted with multiple twisted tape inserts in different arrangement can be discovered by Pareto based multi-objective optimization approach. 

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

multi-objective optimization of tio2-water nanofluid flow in tubes fitted with multiple twisted tape inserts in different arrangement

in this paper, experimentally derived correlations of heat transfer and pressure drop are used in a pareto based multi-objective optimization (moo) approach to find the best possible combinations of heat transfer and pressure drop of tio2-water nanofluid flow in tubes fitted with multiple twisted tape inserts in different arrangement. in this study there are four independent design variables: t...

متن کامل

Enhancements Of Heat Transfer Nanofluid Flow In Circular Pipe With Twisted Tape Inserts: Review

Heat transfer improvement in circular pipe by using nanofluid and twisted tape is presented in this review paper. Experimental and numerical studies are incorporated involving both the range of turbulent and laminar flow. Effect of type and volume fraction of nanofluid on performance of heat transfer was referred along with the length and twist ratio of the tape through the pipe on heat transfe...

متن کامل

Heat Transfer Enhancement of Laminar Nanofluids Flow in a Circular Tube Fitted with Parabolic-Cut Twisted Tape Inserts

Numerical investigation has been carried out on heat transfer and friction factor characteristics of copper-water nanofluid flow in a constant heat-fluxed tube with the existence of new configuration of vortex generator using Computational Fluid Dynamics (CFD) simulation. Two types of swirl flow generator: Classical twisted tape (CTT) and Parabolic-cut twisted tape (PCT) with a different twist ...

متن کامل

Multi-objective optimization of nanofluid flow in microchannel heat sinks with triangular ribs using CFD and genetic algorithms

Abstract In this paper, multi-objective optimization (MOO) of Al2O3-water nanofluid flow in microchannel heat sinks (MCHS) with triangular ribs is performed using Computational Fluid Dynamics (CFD) techniques and Non-dominated Sorting Genetic Algorithms (NSGA II). At first, nanofluid flow is solved numerically in various MCHS with triangular ribs using CFD techniques. Finally, the CFD data will...

متن کامل

Numerical Investigation of Heat Transfer and Friction Factor Characteristics in a Circular Tube Fitted with V-Cut Twisted Tape Inserts

Numerical investigation of the heat transfer and friction factor characteristics of a circular fitted with V-cut twisted tape (VCT) insert with twist ratio (y = 2.93) and different cut depths (w = 0.5, 1, and 1.5 cm) were studied for laminar flow using CFD package (FLUENT-6.3.26). The data obtained from plain tube were verified with the literature correlation to ensure the validation of simulat...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 3  شماره 2

صفحات  89- 99

تاریخ انتشار 2015-06-30

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023