Lattice Boltzmann Simulation of Deformation and Breakup of a Droplet under Gravity Force Using Interparticle Potential Model
نویسنده
چکیده مقاله:
Abstract In this paper interparticle potential model of the lattice Boltzmann method (LBM) is used to simulate deformation and breakup of a falling droplet under gravity force. First this model is applied to ensure that the surface tension effect is properly implemented in this model. Two tests have been considered. First, it has been checked an initial square drop in a 2D domain can freely deform to a circular drop and secondly the coalescence of two static drops that merge to become a single circular drop is simulated. In order to further verify the model, Laplace law for static drops is performed. In the next step, wall effects on the droplet shape and its average velocity have been studied. it is seen that average velocity of droplet at different times is independent of wall effects when the ratio of the width of channel to droplet diameter (W/D) is more than 6. In the final section of the paper deformation and breakup of a falling droplet for some range of Eotvos and Ohnesorge numbers are investigated. It is seen that at very low Eotvos numbers, where the surface tension force is dominant, the droplet deforms slowly and reaches a steady state without breakup. At higher Eotvos numbers gravitational force overcome the surface tension force and the droplet deforms more. For breakup modes at small Ohnesorge number, if Eotvos number be increased to the middle value, the droplet deforms more than from state of low Eotvos number value and eventually forms a backward-facing bag. Finally for high Eotvos numbers, fragments of droplet are sheared from the edges and the shear breakup mechanism is seen. On the other hand the stabilizing effect of the Ohnesorge number, (the ratio of viscous stresses and surface tension) , is shown. At higher Ohnesorge number, the simulations show that the main effect of increasing Ohnesorge number is to move the boundary between the different breakup modes to higher Eotvos number.
منابع مشابه
Simulation of Micro-Channel and Micro-Orifice Flow Using Lattice Boltzmann Method with Langmuir Slip Model
Because of its kinetic nature and computational advantages, the Lattice Boltzmann method (LBM) has been well accepted as a useful tool to simulate micro-scale flows. The slip boundary model plays a crucial role in the accuracy of solutions for micro-channel flow simulations. The most used slip boundary condition is the Maxwell slip model. The results of Maxwell slip model are affected by the ac...
متن کاملForce method in a pseudo-potential lattice Boltzmann model
Single component pseudo-potential lattice Boltzmann models have been widely studied due to their simplicity and stability in multiphase simulations. While numerous model have been proposed, comparative analysis and advantages and disadvantages of different force schemes is often lacking. A pseudo-potential model to simulate large density ratios proposed by Kupershtokh et al. [1] is analyzed in ...
متن کاملComparison of Lattice Boltzmann simulation of droplet evaporation and experiments
By using a lattice Boltzmann method for simulating droplet evaporation (R. Ledesma-Aguilar et al., Soft Matter, 2014, 10, 8267) we investigate the evaporation of single and multiple droplets. The numerical results show a good agreement with experiments of the evaporation of alcohol droplets in water with regards to the typical timescales and the convection fields. We also show the slow-down in ...
متن کاملNumerical Simulation of Fluid Flow Past a Square Cylinder Using a Lattice Boltzmann Method
The method of lattice boltzmann equation(LBE) is a kinetic-based approach for fluid flow computations. In the last decade, minimal kinetic models, and primarily the LBE, have met with significant success in the simulation of complex hydrodynamic phenomena, ranging from slow flows in grossly irregular geometries to fully developed turbulence, to flow with dynamic phase transitions. In the presen...
متن کاملGravity in a lattice Boltzmann model
In this paper we consider the introduction of a body force, in the incompressible limit, into the lattice Boltzmann model. A number of methods are considered and their suitability to our objectives determined. When there is no density variation across the fluid, gravity can be introduced in the form of an altered pressure gradient. This method correctly satisfies the Navier-Stokes equation; how...
متن کاملFour different types of a single drop dripping down a hole under gravity by lattice Boltzmann method
In this paper the dynamic of a droplet on a surface with a hole is investigated under gravitational effect by using lattice Boltzmann method. Incompressible two-phase flow with high density ratio proposed by Lee is considered. Cahn’s theory is used to observe the wettability of the surface in contact with liquid and gas phases. Several parameters such as contact angle, surface tension and gravi...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 26 شماره 7
صفحات 781- 794
تاریخ انتشار 2013-07-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023