Kinetic investigation of carbon nanotube deposition by DC electrophoretic technique

نویسندگان

  • A. R. Gardeshzadeh Department of Nanomaterials and Nanocoatings, Institute for Color Science and Technology
  • S. Rasouli Department of Nanomaterials and Nanocoatings, Institute for Color Science and Technology
چکیده مقاله:

In this paper, kinetics of DC electrophoretic deposition EPD of carbon nanotubes CNTs is investigated. Carbon nanotubes suspended in pure ethanol with addition of magnesium nitrate was used as deposition media. The effect of main EPD parameters such as deposition time, applied voltage and the CNT concentration on deposit yield was investigated. The variation of current density vs. time and the effect of magnetic stirring were also examined. The results are in good agreement with Hamaker´s law and the deposit yield increases with voltage and CNT concentration but there is a deviation from linear trend in longer deposition times. Stirring could compensate some of this deviation but increases the current density fluctuations.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

ELECTROPHORETIC DEPOSITION OF TIO2-MULTI-WALLED CARBON NANOTUBE COMPOSITE COATINGS: MORPHOLOGICAL STUDY

A homogenous TiO2 / multi-walled carbon nanotubes(MWCNTs) composite film were prepared by electrophoretic co-deposition from organic suspension on a stainless steel substrate.  In this study, MWCNTs was incorporated to the coating because of their long structure and their capability to be functionalized by different inorganic groups on the surface. FTIR spectroscopy showed the existence of...

متن کامل

Preparation of Nanohydroxyapatite-Carbon Nanotube Composite Coatings on 316L Stainless Steel Using Electrophoretic Deposition

Nanohydroxyapatite-carbon nanotube composite coatings were deposited via electrophoretic deposition (EPD). AISI 316L stainless steel and ethanol were used as substrate and dispersing medium, respectively. 5%wt carbon nanotube (CNT) was used as reinforcing phase. Uniform and macrocrack-free coatings were obtained both for hydroxyapatite (HA) and HA-5%wt CNT coatings. Scanning electron micros...

متن کامل

Novel carbon nanotube network deposition technique for electronic device fabrication

Marina Y. Zavodchikova*,1, Albert G. Nasibulin1, Tero Kulmala2, Kestutis Grigoras2, Anton S. Anisimov1, Sami Franssila2, Vladimir Ermolov3, and Esko I. Kauppinen1 1 NanoMaterials Group, Laboratory of Physics and Center for New Materials, Helsinki University of Technology, Espoo, Finland 2 Microfabrication Group, Micro and Nanosciences Laboratory, Helsinki University of Technology, Espoo, Finlan...

متن کامل

Electrophoretic Deposition of Hydroxyapatite

     The purpose of this study was to investigate the deposition of the hydroxyapatite (HA) coating via the electrophoresis procedure. The HA deposition was performed in an ethanol, methanol, acetone and isopropanol suspension. Methanol was found to be the best deposition media. Among the different environmental conditions, including the encapsulation of the samples under two vacuum types of pr...

متن کامل

Electrophoretic Deposition of Microwave Combustion Synthesized Hydroxyapatite and Its Carbon Nanotube Reinforced Nanocomposite on 316L Stainless Steel

Nanohydroxyapatite-carbon nanotube Nanocomposite (HA-CNT) coatings were deposited via electrophoretic deposition (EPD). Hydroxyapatite was synthesized via microwave combustion method using calcium nitrate and glycing as starting materials. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) revealed that pure hydroxyapatite nanoparticles have been synthesized. AISI 316L s...

متن کامل

Electrophoretic deposition of carbon nanotube on reticulated vitreous carbon for hexavalent chromium removal in a biocathode microbial fuel cell

For Cr(VI)-removal microbial fuel cell (MFC), a more efficient biocathode in MFCs is required to improve the Cr(VI) removal and electricity generation. RVC-CNT electrode was prepared through the electrophoretic deposition of carbon nanotube (CNT) on reticulated vitreous carbon (RVC). The power density of MFC with an RVC-CNT electrode increased to 132.1 ± 2.8 mW m-2, and 80.9% removal of Cr(VI) ...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 4  شماره 1

صفحات  51- 58

تاریخ انتشار 2011-09-07

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023