Finite Element Simulation of Hydrostatic Extrusion Process to Produce Thin Bimetallic Parts

نویسندگان

  • Ali Delfani Department of Mechanical Engineering, Jami Institute of Technology, Isfahan, Iran
  • Hamid Montazerolghaem Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran|Modern Manufacturing Technologies Research Center, Najafabad Branch, Islamic Azad University, Najafabad, Iran
چکیده مقاله:

The hydrostatic extrusion is a new method of extrusion process. The most important advantage of this method is reduction of friction and close tolerance for the coating thickness. In this study, the hydrostatic extrusion simulation of bimetallic wires has performed using of finite element method. In the following the advantages of hydrostatic extrusion compared to the direct extrusion are presented.It can be concluded that by increasing the friction coefficient between the work piece and the die, the extrusion force value also increases. Increasing the cross-section reduction when the die angle kept constant as a result of increase in die length, consequently leads to an increase in the extrusion force.Regarding to the absence of friction in the die and almost uniformly deformation and homogeneous in the hydrostatic extrusion, the product with a uniform coating thickness can be obtained as it is very important for manufacture of very high length bi-metal products. 

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Experimental and Finite Element Analyses of the Hydrostatic Cyclic Expansion Extrusion (HCEE) Process with Back-Pressure

It is generally known that severe plastic deformation processes with back pressure not only apply higher hydrostatic stress and more deformation compared to what a regular process can apply to a workpiece but also prevent surface defects in the workpiece during the process. Hydrostatic cyclic expansion extrusion (HCEE) was developed recently for processing long ultrafine-grained metals and allo...

متن کامل

Numerical Simulation of Three-Dimensional Extrusion Process Using hp-Adaptive Finite Element Model

Extrusion of aluminum sections is analyzed with a solution hp-adaptive finite element model. The analysis is based on the assumption that the elastic effects are negligible and rigid-viscoplastic material behavior is acceptable. The equations governing the flow of incompressible non-Newtonian fluids are solved using an iterative penalty finite element model. An error estimation scheme based on ...

متن کامل

Finite element simulation of two-point incremental forming of free-form parts

Two-point incremental forming method is considered a modern technique for manufacturing shell parts. The presence of bottom punch during the process makes this technique far more complex than its conventional counterpart i.e. single-point incremental forming method. Thus, the numerical simulation of this method is an essential task, which leads to the reduction of trial/error costs, predicts th...

متن کامل

Numerical study and genetic algorithm optimization of hot extrusion process to produce rectangular waveguides

Rectangular waveguide is one of the earliest types of transmission lines. Rectangular waveguide can be produced by hot extrusion process. In this paper, the hot extrusion process of CuZn5 rectangular waveguide was investigated by Finite Element Method (FEM). In addition, Genetic Algorithm (GA) was used to optimize the die geometry and process conditions to achieve the lowest magnitude of extrus...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 6  شماره 4

صفحات  59- 68

تاریخ انتشار 2017-11-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023