Finite Element Method for Static Cyclic Behavior of Steel Shear Wall with Corrugated Plates
نویسندگان
چکیده مقاله:
The system of steel shear wall is an initiative resistance system against the lateral load such as an earthquake and the wind that has been researched in the last three decades. Currently, this system is noticed more than other systems because of adequate stiffness, ductility, and more energy absorption. The system of steel shear wall with corrugated sheets has been offered as an innovative system, since the construction of panels for hard-set steel shear wall is expensive and also it causes the increscent of weight construction. This type of system has been developed using of hard outer plate from geometry of corrugation shape that has better buckling strength than hard-set and flat case in this study. This study is conducted to compare the strength and energy dissipation capacity of three different steel shear walls: unstiffened, trapezoidally vertical corrugated and trapezoidally horizontal corrugated under vibration load of AISC 341-10 instruction with 100mm movement. The results reveal that although the ultimate strength of the unstiffened model is nearly 17% larger compared to that of the corrugated models, energy dissipation capacity of the corrugated models are approximately 52% larger compared to the unstiffened model.
منابع مشابه
buckling of viscoelastic composite plates using the finite strip method
در سال های اخیر، تقاضای استفاده از تئوری خطی ویسکوالاستیسیته بیشتر شده است. با افزایش استفاده از کامپوزیت های پیشرفته در صنایع هوایی و همچنین استفاده روزافزون از مواد پلیمری، اهمیت روش های دقیق طراحی و تحلیل چنین ساختارهایی بیشتر شده است. این مواد جدید از خودشان رفتارهای مکانیکی ارائه می دهند که با تئوری های الاستیسیته و ویسکوزیته، نمی توان آن ها را توصیف کرد. این مواد، خواص ویسکوالاستیک دارند....
investigation on diagonal reinforced concrete shear walls behavior under cyclic lateral load using finite element method
buildings with wall or frame-wall systems are more effective against earthquake forces and sustain less damage than buildings which their lateral resistance is solely depends on frames. four reinforced concrete (rc) structural wall specimens were subjected to cyclic loading using finite elements method with abaqus software in order to study influence of diagonal web reinforcement. the research ...
متن کاملSpectral Finite Element Method for Free Vibration of Axially Moving Plates Based on First-Order Shear Deformation Theory
In this paper, the free vibration analysis of moderately thick rectangular plates axially moving with constant velocity and subjected to uniform in-plane loads is investigated by the spectral finite element method. Two parallel edges of the plate are assumed to be simply supported and the remaining edges have any arbitrary boundary conditions. Using Hamilton’s principle, three equations of moti...
متن کاملFinite Element Instability Analysis of the Steel Joist of Continuous Composite Beams with Flexible Shear Connectors
Composite steel/concrete beams may buckle in hogging bending regions. As the top flange of I-beam in that arrangement is restricted from any translational deformation and twist, the web will distort during buckling presenting a phenomenon often described as restricted distortional buckling. There are limited studies available in the literature of restricted distortional buckling of composite st...
متن کاملComparison of plasticity and stiffness of steel shear walls with composite steel plate shear wall
The steel shear wall and composite steel plate shear wall is introduced in recent three decade and is considered and is spread rapidly. Composite steel plate shear wall which is made of a layer of thin steel sheet with coating of reinforced concrete in one or both sides of steel palate is considered a third generation of resistance shear walls against lateral loads that in addition to increasin...
متن کاملImproving Cyclic Behavior of Steel Plate Shear Walls with Elliptical Perforations
In this paper, the effect of elliptical shape openings was numerically compared to the case when circular openings were used in the steel panel shear walls. At first, the finite element model in ABAQUS was calibrated by experimental results, obtained from previous studies. Then, three steel shear panels with different sizes of elliptical openings were analyzed under cyclic loads, and the result...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 7 شماره 1
صفحات 23- 29
تاریخ انتشار 2017-03-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
کلمات کلیدی
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023