EXPERIMENTALl ANALYSIS OF PARTITION COEFFICIENT IN Al-Mg ALLOYS
نویسندگان
چکیده مقاله:
Because the partition coefficient is one of the most important parameters affecting microsegregation, the aim of this research is to experimentally analyse the partition coefficient in Al-Mg alloys. In order to experimentally measure the partition coefficient, a series of quenching experiments during solidification were carried out. For this purpose binary Al-Mg alloys containing 6.7 and 10.2 wt-% Mg were melted and solidified in a DTA furnace capable of quenching samples during solidification. Cooling rates of 0.5 and 5 K/min were used and samples were quenched from predetermined temperatures during solidification. The fractions and compositions of the phases were measured by quantitative metallography and SEM/EDX analyses, respectively. These results were used to measure the experimental partition coefficients. The resultant partition coefficients were used to model the concentration profile in the primary phase and the results were compared with equilibrium calculations and experimental profiles. The results of calculations based on the experimental partition coefficients show better consistency with experimental concentration profiles than the equilibrium calculations.
منابع مشابه
THERMAL ANALYSIS AND KINETICS OF THE PRECIPITATION IN WROUGHT Al-Mg, Al-Mg-ScAND Al-Mg-Sc-Me (Me=Zr, Ti) ALLOYS
Precipitation behaviour of wrought Al-6Mg alloys with ternary scandium and quaternary zirconium and titanium has been studied. Hardness measurements and resistivity studies are employed to assess the precipitation behaviour of scandium doped Al-6Mg alloy without or with quaternary additions of zirconium and titanium. Further, the kinetics of precipitations are studied by differential scanning c...
متن کاملMelt Protection of Mg-Al Based Alloys
This paper reports the current status of Mg melt protection in view to identify near-future challenges, but also opportunities, for Mg melt protection of Mg-Al based alloys. The goal is to design and manufacture sustainable Mg alloys for resource efficiency, recycling and minimising waste. Among alternative cover gas technologies for Mg melt protection other than SF6: commercially available tec...
متن کاملCASTABILITY OF Al-Li-Mg AND Al-Li-Cu-Mg ALLOYS
The objective of the present work is to study the casting characteristics of various A1-Li alloys, which include fluidity and strengths of the alloys and their interaction with cast molds. Materials investigated are Al-Li-Mg and Al-Li-Cu-Mg alloys with Li content of 2.5 wt%. The results show that sand molds with resin binders are good for A1-Li casting. Ceramic coatings can further reduce the m...
متن کاملOxidation Processes and Phase Changes in Metastable Al–Mg Alloys
Oxidation behavior of metastable mechanical alloys in the Al–Mg binary system has been examined in the context of high-energy density materials and combustion applications. Mechanical alloy powders with compositions ranging from Al0.95Mg0.05 to Al0.5Mg0.5, as well as the component metals, were heated at 20 K/min in oxygen. Differential thermal analysis and thermogravimetric analysis showed that...
متن کاملSerrated flow in nanostructured binary Mg-Al alloys
Article history: Received 2 August 2016 Received in revised form 14 September 2016 Accepted 15 September 2016 Available online xxxx Serrated flow, also known as the Portevin-Le Chatelier effect, has been extensively investigated in binary Mg-alloys such asMg-Ag,Mg-Y andMg-Li alloys. Interestingly, however, this effect has not been observed inMg-Al alloys. In this work, we report the appearance ...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 13 شماره 2
صفحات 62- 72
تاریخ انتشار 2016-06
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023