Experimental and numerical study of delamination detection in a WGF/epoxy composite plate using ultrasonic guided waves and signal processing tools
نویسندگان
چکیده مقاله:
Reliable damage detection is one of the most critical tasks in composite plate structures. Ultrasonic guided waves are acknowledged as an effective way of structural health monitoring (SHM). In this research, ABAQUS FE package is employed in order to develop a 3D finite element (FE) model to investigate the wave propagating features in a four-layer Woven Glass fiber (WGF) /epoxy composite plate. Dispersion curves have been extracted using semi-analytical finite element (SAFEM) in MATLAB. An experimental study has been done to obtain the sensitivity of the excitation frequency on the delamination detection problem. The Fast Fourier Transform (FFT), Butterworth filtering and the Continuous Wavelet Transform (CWT) signal processing methods have been utilized to extract a more accurate damage sensitive feature from experimental signals.Calculations of amplitude reduction ratio (ARR) for both raw and filtered signals shows that increasing the excitation frequency, which means decreasing the wavelength, leads to increase in the ARR in an approximately linear manner for raw signals, while using the filtered signals for ARR extraction yields higher ARR, peaked at the tuned Lamb mode, which is F=330 kHz in the study. The Butterworth filtering provides larger damage sensitive feature compared to CWT method. Consequently, the ARR is a reliable and enough sensitive feature for delamination detection in composite plates, especially when extracted from filtered signals
منابع مشابه
Experimental Detection of Composite Delamination Damage based on Ultrasonic Infrared Thermography
An experimental setup is designed to detect composite delamination damage based on ultrasonic infrared thermography. The ultrasonic infrared thermography system is composed by ultrasonic excitation system, infrared thermal imager and data acquisition system and two damaged composite plate specimens are produced in the experiment. The image processing methods including thresholding, filters, edg...
متن کاملApplication of Wavelet Transform as a Signal Processing Method for Defect Detection using Lamb Waves: Experimental Verification
A Lamb wave-based crack detection method for aluminum plates health monitoring is developed in this paper. Piezoelectric disks are employed to actuate and capture the Lamb wave signals. The position of crack is assumed to be aligned with the sensor and actuator. Extraction of high quality experimental results of lamb wave propagation in a plate-like structure is considerably complicated due to...
متن کاملGuided Ultrasonic Waves for Impact Damage Detection in Composite Panels
Carbon fiber laminate composites, consisting of layers of polymer matrix reinforced with high strength carbon fibers, are increasingly employed for aerospace structures. They offer advantages for aerospace applications, e.g., good strength to weight ratio. However, impact during the operation and servicing of the aircraft can lead to barely visible and difficult to detect damage. Depending on t...
متن کاملa contrastive study of rhetorical functions of citation in iranian and international elt scopus journals
writing an academic article requires the researchers to provide support for their works by learning how to cite the works of others. various studies regarding the analysis of citation in m.a theses have been done, while little work has been done on comparison of citations among elt scopus journal articles, and so the dearth of research in this area demands for further investigation into citatio...
Detection of delamination defects in carbon fiber using ultrasonic signal processing
In this work, the ultrasonic signals are modelled as a superposition of many Gaussian echoes with unknown parameters. The detection of ultrasonic echoes using Maximum A Posteriori estimation principle, based on the prior knowledge of the spectral characteristic of the ultrasonic transducer, has been used in order to estimate the unknown parameters. A simulation study validated by experimentatio...
متن کاملDamage detection and structural health monitoring of ST-37 plate using smart materials and signal processing by artificial neural networks
Structural health monitoring (SHM) systems operate online and test different materials using ultrasonic guided waves and piezoelectric smart materials. These systems are permanently installed on the structures and display information on the monitor screen. The user informs the engineers of the existing damage after observing signal loss which appears after damage is caused. In this paper health...
متن کاملمنابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ذخیره در منابع من قبلا به منابع من ذحیره شده{@ msg_add @}
عنوان ژورنال
دوره 4 شماره 2
صفحات 141- 152
تاریخ انتشار 2018-07-01
با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.
میزبانی شده توسط پلتفرم ابری doprax.com
copyright © 2015-2023