Characterization of TiN, CrN and (Ti, Cr) N Coatings Deposited by Cathodic ARC Evaporation

نویسنده

چکیده مقاله:

In this investigation PVD Ti-Cr)N coatings were deposited on hardened and tempered tool steel substrates using reactive arc evaporation. Physical and mechanical properties of coatings such as roughness, thickness, phase composition, hardness and modulus young and coefficient friction were evaluated. Phase compositions were studies by X-ray diffraction method. The surface microstructure and morphology were  studied using scanning electron microscope (SEM) and coating compositions were determined by energy dispersive spectroscopy (EDS).  Mechanical Properties were determined by Nano indentation. The friction behavior of the coatings were investigated using ball-on-disc test under normal loads of 7 .The results showed that(Ti, Cr)N and TiN coating had only one solid solution cubic phase While CrN coatings had Hexagonal Cr2N and Cubic CrN phases. Average grain size of the coatings was found in the range of 14 to 20 nm. Physical-Mechanical Properties of CrN and (Ti, Cr)N and TiN coatings, respectively, increases. Mechanical behavior of the (Ti, Cr)N coatings is related to Ti content and hardness decreases with decreasing Ti content.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

COMPARISON OF THE CrN , TiN AND (Ti, Cr)N PVD COATINGS DEPOSITED BY CATHODIC ARC EVAPORATION

In the present study, CrN, TiN and (Ti, Cr)N coatings were deposited on D6 tool steel substrates. Physical and mechanical properties of coatings such as microstructure, thickness, phase composition, and hardness were evaluated. Phase compositions were studies by X-ray diffraction method. Mechanical properties were determined by nano-indentation technique. The friction and wear behaviour of the ...

متن کامل

Synthesis and characterization of Cr–B–N coatings deposited by reactive arc evaporation

Nanocomposite Cr–B–N coatings were deposited from CrB0.2 compound targets by reactive arc evaporation using an Ar/N2 discharge at 500 °C and −20 V substrate bias. Elastic recoil detection (ERDA), x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), and selected-area electron diffraction (SAED) were used to study the effect of...

متن کامل

Evaluation of tribological properties of (Ti,Al)CN/DLC composite coatings deposited by cathodic arc method.

In this study, Ti, Al and N doped DLC – referred to here after as “(Ti,Al)CN/DLC composite”- coating and pure diamond-like coating (DLC) were produced by cathodic arc deposition technique and the effects of the coating thickness on their tribological properties were evaluated. The coatings were characterized, using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffrac...

متن کامل

Ti-Cr-N Coatings Deposited by Physical Vapor Deposition on AISI D6 Tool Steels

In this study, physical vapor deposition (PVD) Ti-Cr-N coatings were deposited at two different temperatures 100 and 400ºC on hardened and tempered tool steel substrates. The influence of the applied deposition temperature on the physical and mechanical properties of coatings such as roughness, thickness, phase composition, hardness and Young’s modulus were evaluated. Phase compositions were st...

متن کامل

ti-cr-n coatings deposited by physical vapor deposition on aisi d6 tool steels

in this study, physical vapor deposition (pvd) ti-cr-n coatings were deposited at two different temperatures100 and 400ºc on hardened and tempered tool steel substrates. the influence of the applied deposition temperature on the physical and mechanical properties of coatings such as roughness, thickness, phase composition, hardness and young’s modulus were evaluated. phase compositions were stu...

متن کامل

Comparison of Properties of Ti/TiN/TiCN/TiAlN Film Deposited by Cathodic Arc Physical Vapor and Plasma-assisted Chemical Vapor Deposition on Custom 450 Steel Substrates

This study investigated the effects of deposition techniques on the microstructural and tribological properties of Ti/TiN/TiCN/TiAlN multilayer coatings onto a Custom 450 steel substrate. The coatings were produced using cathodic arc physical vapor deposition (CAPVD) and plasma-assisted chemical vapor deposition (PACVD). The microstructural of the coatings was evaluated using (SEM), and phase f...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 27  شماره 7

صفحات  1127- 1132

تاریخ انتشار 2014-07-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023