CFD Simulation of Dimethyl Ether Synthesis from Methanol in an Adiabatic Fixed-bed Reactor

نویسندگان

  • Mohammad Reza Irani Research Institute of Petroleum Industry (RIPI)
  • Reza Mosayebi Behbahani Department of Gas Engineering, Petroleum University of Technology
چکیده مقاله:

A computational fluid dynamic (CFD) study of methanol (MeOH) to dimethyl ether (DME) process in an adiabatic fixed-bed reactor is presented. One of the methods of industrial DME production is the catalytic dehydration of MeOH. Kinetic model was derived based on Bercic rate. The parameters of this equation for a specific catalyst were tuned by solving a one-dimensional homogenous model using MATLAB optimization module. A two-dimensional CFD simulation of the reaction is demonstrated and considered as numerical experiments. A sensitivity analysis was run in order to find the effect of temperature, pressure, and WHSV on the reactor performance. Good agreement was achieved between bench experimental data and the model. The results show that the maximum conversion of reaction (about 85.03%) is obtained at WHSV=10 h-1 and T=563.15 K, whereas the inlet temperature has a greater effect on methanol conversion. Moreover, the effect of water in inlet feed on methanol conversion is quantitatively studied. It was concluded that the results obtained from CFD analysis give precise guidelines for further studies on the optimization of reactor performance.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

cfd simulation of dimethyl ether synthesis from methanol in an adiabatic fixed-bed reactor

a computational fluid dynamic (cfd) study of methanol (meoh) to dimethyl ether (dme) process in an adiabatic fixed-bed reactor is presented. one of the methods of industrial dme production is the catalytic dehydration of meoh. kinetic model was derived based on bercic rate. the parameters of this equation for a specific catalyst were tuned by solving a one-dimensional homogenous model using mat...

متن کامل

Steady State Operability Characteristics of an Adiabatic Fixed-Bed Reactor for Methanol Dehydration

Operability analysis as one of the most important bridges between process design and process control helps the process designer to investigate the control issues quite early in the design stage. Recently, Vinson and Georgakis suggested a steady state geometrical operability index as a quantitative measure for assessment of process operability. In...

متن کامل

Modeling, Simulation and Control of a Tubular Fixed-bed Dimethyl Ether Reactor

This paper considers the modeling and control of a tubular fixed bed reactor with recycle stream for dimethyl ether (DME) production. For simulation purposes, a pseudo homogeneous model has been developed. By reactor simulation under steady state condition, effects of parameters such as feed rate, pressure and shell temperature are investigated. Using the steady state model, an optimizer that m...

متن کامل

steady state operability characteristics of an adiabatic fixed-bed reactor for methanol dehydration

operability analysis as one of the most important bridges between process design and process control helps the process designer to investigate the control issues quite early in the design stage. recently, vinson and georgakis suggested a steady state geometrical operability index as a quantitative measure for assessment of process operability. in this paper, dme fixed-bed reactor is heterogeneo...

متن کامل

Simulation and Control of a Methanol-To-Olefins (MTO) Laboratory Fixed-Bed Reactor

In this research, modeling, simulation, and control of a methanol-to-olefins laboratory fixed-bed reactor with electrical resistance furnace have been investigated in both steady-state and dynamic conditions. The reactor was modeled as a one-dimensional pseudo-homogeneous system. Then, the reactor was simulated at steady-state conditions and the effect of different parameters including...

متن کامل

Modelling and simulation of a direct synthesis of dimethyl ether (DME) in a tubular reactor with a hybrid catalyst bed

This work includes a modelling and simulation of dimethyl ether direct synthesis in a tubular type reactor with hybrid catalysts bed. The results of simulation show that the loading ratio of methanol synthesis and dehydration catalysts has a important influence on product yield.

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ذخیره در منابع من قبلا به منابع من ذحیره شده

{@ msg_add @}


عنوان ژورنال

دوره 2  شماره 2

صفحات  50- 64

تاریخ انتشار 2013-04-01

با دنبال کردن یک ژورنال هنگامی که شماره جدید این ژورنال منتشر می شود به شما از طریق ایمیل اطلاع داده می شود.

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023