Silk suture reinforced with Cefixime nanoparticles using polymer hydrogel (CFX@PVA); Preparation, Bacterial resistance and Mechanical properties
Authors
Abstract:
Objective(s): The objective of the current study was to prevent surgical site infection (SSI) by creating a new antibacterial silk suture. Methods: Cefixime trihydrate (CFX) was prepared as nanoparticles via mixing with polyvinyl alcohol (PVA) hydrogel by covalent cross-linkage. The mixture was stirred vigorously to obtain a homogenous gel. Under this condition the polymer chains separate CFX as nanoparticles and trap them (CFX@PVA). The enrichment of silk suture was performed by immersing it in the CFX@PVA solution. The trapped CFX nanoparticles in PVA hydrogel on the surface of sutures were confirmed by SEM. The effect of CFX@PVA silk sutures on tensile strength was analyzed, using a Santammachine controller. The antibacterial activity of the reinforced silk suture was tested on E. coli (ATCC25922) and S. aureus (ATCC25924). Results: All antibacterial studies clearly showed that the use of novel CFX@PVA silk sutures could represent clinical advantages, in terms of prevention of resistant bacteria, such as Staphylococcus aureus (S. aureus), the same as the sensitive bacteria, for 15 days. The maximum elongation of composite before rupture, modulus and extension, showed statistically significant difference between reinforced silk sutures and untreated silk suture. No statistically significant difference was found between the Failure load, Stress, Bending and Energy. Conclusions: Our data indicate that CFX@ Silk sutures are capable of reducing the risk of SSIs, and has a good mechanical strength to keep the wound sides closed, during early healing recovery.
similar resources
Studying the Mechanical and Thermal Properties of Polymer Nanocomposites Reinforced with Montmorillonite Nanoparticles Using Micromechanics Method
In this study, the mechanical and thermal behavior of the nano-reinforced polymer composite reinforced by Montmorillonite (MMT) nanoparticles is investigated. Due to low cost of computations, the 3D representative volume elements (RVE) method is utilized using ABAQUS finite element commercial software. Low density poly ethylene (LDPE) and MMT are used as matrix and nanoparticle material, respec...
full textThermo-mechanical properties of polymer nanocomposites reinforced with randomly distributed silica nanoparticles- Micromechanical analysis
A three-dimensional micromechanics-based analytical model is developed to study thermo-mechanical properties of polymer composites reinforced with randomly distributed silica nanoparticles. Two important factors in nanocomposites modeling using micromechanical models are nanoparticle arrangement in matrix and interphase effects. In order to study these cases, representative volume element (RVE)...
full textPreparation of hydrogel substrates with tunable mechanical properties.
The modulus of elasticity of the extracellular matrix (ECM), often referred to in a biological context as "stiffness," naturally varies within the body, e.g., hard bones and soft tissue. Moreover, it has been found to have a profound effect on the behavior of anchorage-dependent cells. The fabrication of matrix substrates with a defined modulus of elasticity can be a useful technique to study t...
full textPreparation of elastic silk sericin hydrogel.
This paper reports a preparation method for silk sericin hydrogel using the Sericin-hope silkworm, whose cocoons consist almost exclusively of sericin. Sericin solution, prepared from Sericin-hope cocoons, contains intact sericin and forms elastic hydrogels with the addition of ethanol. The sericin hydrogel can be prepared without crosslinking by chemicals or irradiation and might be usable as ...
full textMechanical properties of multi-walled carbon nanotubes reinforced polymer nanocomposites
Carbon nanotubes (CNTs ) are considered to be one of the novel reinforcement for developing advanced nanocomposites due to their outstanding thermo-mechanical properties. Multi-walled carbon nanotubes (MWCNTs ) are developed by arc discharge method. To enhance the dispersion of CNTs in polymer matrix, CNTs are modified with chemical treatment and processed by ultrasonication process. Surface ch...
full textMechanical Properties of Green Coconut Fiber Reinforced Hdpe Polymer Composite
During the last few years, natural fibers have received much more attention than ever before from the research community all over the world. These natural fibers offer a number of advantages over traditional synthetic fibers. The present study aims to determine the mechanical properties namely, Tensile strength (TS), Flexural strength (FS), and Impact strength (IS) of green coconut fiber reinfo...
full textMy Resources
Journal title
volume 3 issue 3
pages 133- 139
publication date 2018-09-01
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023