Effect of Different Welding Parameters on the Mechanical and Microstructural Properties of Stainless Steel 304H Welded Joints
Authors
Abstract:
In this research work, an attempt has been made to examine the different welding parameters which affect the weldability of 304H Austenitic stainless steel (ASS) welded joint using the proper filler wire. Chemical composition of filler wire was same as that of base metal. Further this study addressed the combined effect of various welding parameters on the metallurgical and mechanical properties of the weldments. Welding was carried out at different parameters such as welding wire speed, shielding gas flow rate, welding current and arc voltage etc. Tensile tests and V-notch Charpy tests were conducted as per ASTM to determine the mechanical properties of the welded specimens. In order to determine the microstructured changes that occurred, the interface regions of the welded specimens were examined by microscope. As a result, it is reported that changing the shielding gas flow rate and wire feed speed affects the microstructure and mechanical properties of weldment. Impact tests reveal that toughness of the welded joint increases with increasing in welding current, while ultimate tensile strength (UTS) first increases and then decreases.
similar resources
Investigating the Effect of Optimum Welding Parameters on the Microstructural and Mechanical Properties of St37 Steel and 316L Stainless Steel Welded by the Friction Stir Welding Process
In this research, St37 and 316L steel sheets were welded using friction stir welding (FSW) process and effective parameters such as the rotational speed, linear speed of the tool, pin diameter, and their appropriate values were studied. The microstructure, hardness, and strength of the different welding regions were investigated. It was observed that in the stir zone (SZ), a mechanical operatio...
full textThe Effect of Welding Energy on the Microstructural and Mechanical Properties of Ultrasonic-Welded Copper Joints
The effects of welding energy on the mechanical and microstructural characteristics of ultrasonic-welded pure copper plates were investigated. Complex dynamic recrystallization and grain growth occurred inside the weld zone during ultrasonic welding. At a low welding energy, a thin band of straight weld interfaces was observed and had an ultra-fine grain structure. With an increase in welding e...
full textEffect of Welding Parameters in the Microstructure and Mechanical Properties of Friction-Welded Joints of 100Cr6 Steel
In this study, high-carbon, chromium alloy steel (100Cr6) having the initial spheroidized microstructure was welded using the rotary friction welding method. The effects of process parameters such as friction time and friction force were experimentally investigated. The friction welded joints were produced of two 100Cr6 steel rods. In order to examine the microstructure and mechanical properti...
full textStudy on the Effect of Laser Welding Parameters on the Microstructure and Mechanical Properties of Ultrafine Grained 304L Stainless Steel
In the present study, an ultrafine grained (UFG) 304L stainless steel with the average grain size of 300 nm was produced by a combination of cold rolling and annealing. Weldability of the UFG sample was studied by Nd: YAG laser welding under different welding conditions. Taguchi experimental design was used to optimize the effect of frequency, welding time, laser current and laser pulse duratio...
full textEffect of Tool Rotational Speed on the Tensile and Microstructural Properties of Friction Stir Welded Different Grades of Stainless Steel Joints
Friction stir welding is a relatively new solid state joining process, which is suitable for welding similar and dissimilar materials. The present research work concentrates on the effect of tool rotational speed on the tensile, microstructural properties and microhardness of the friction stir welded joints of different grades of austenitic stainless steel sheets. Four different tool rotationa...
full textA study on the effect of pulsed current gas tungsten arc welding parameters on the microstructural evolutions, corrosion behavior and mechanical properties of AA 5456 weld joints
Nowadays, aluminum and its alloys have extensive applications in marine and aerospace industrious owing to their excellent properties. Among these alloys, 5xxx series of aluminum alloys have also excellent corrosion resistance, high toughness and strength and also good weldability. Decrease in yield strength and also tensile strength due to the grain growth in the heat affected zone is of the m...
full textMy Resources
Journal title
volume 30 issue 10
pages 1592- 1598
publication date 2017-10-01
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023