Dissimilar Welding of EN 10025 Carbon Steel to AISI 316L Stainless Steel by Friction Stir Welding
Authors
Abstract:
In the present Study, a dissimilar joint of carbon steel sheet EN 10025 with 316 L has been welded by FSW and the welding parameters were optimized by RSM software method. For investigation of mechanical properties and microstructural analysis carried out by using optical, scanning electron microscopes with EDS analysis, tensile and hardness test of different area of joints, SZ, TMAZ, HAZ, their interfaces and Base metal. The optimized result were shown that best of joints within maximum strength (UTS) 312 MPa by rotational speed 950 rpm, transverse speed 90 mm/min and tool angle 3° was achieved. The failures were happened at base metal of EN 10025 to advancing side. Metallographic results were shown that grain size at SZ is 10 to 20 time more reduced caused improved of mechanical properties. Also chemical analysis and hardness result on welded samples by optimized parameters were shown that quite good mixing was happened at SZ.
similar resources
Dissimilar resistance spot welding of AISI 1075 eutectoid steel to AISI 201 stainless steel
In this paper, dissimilar resistance spot welding of AISI 1075 eutectoid steel to AISI 201 stainless steel is investigated experimentally. For this purpose, the experiments are designed using response surface methodology and based on four-factor, five-level central composite design. The effects of process parameters such as welding current, welding time, cooling time and electrode force are inv...
full textdissimilar resistance spot welding of aisi 1075 eutectoid steel to aisi 201 stainless steel
in this paper, dissimilar resistance spot welding of aisi 1075 eutectoid steel to aisi 201 stainless steel is investigated experimentally. for this purpose, the experiments are designed using response surface methodology and based on four-factor, five-level central composite design. the effects of process parameters such as welding current, welding time, cooling time and electrode force are inv...
full textFeasibility study of friction stir welding of 6061-T6 aluminium alloy with AISI 1018 steel
The present work demonstrates that friction stir welding (FSW) is a feasible route for joining 6061 aluminium (Al) alloy to AISI 1018 steel. The weld has a good weld quality and is free of cracks and porosity. The tensile failure happened at the boundary between the nugget and thermomechanically affected zone of the base Al alloy, indicating that the weld has a higher joining strength. Despite ...
full textOptimization of Operating Parameters for Autogenous Welding of AISI 316L Stainless Steel and Steel Using Pulsed Nd: YAG Laser
An attempt made to optimize the operating parameters involved in an autogenous pulsed Nd: YAG laser welding process of similar and dissimilar combinations of butt joint of 2 mm thick 316 L stainless steel and mild steel. Influence of prominent laser welding parameters such as average peak power, defocus position, spot position, and shielding gas were investigated for welded joints considered. T...
full textInvestigating the Effect of Optimum Welding Parameters on the Microstructural and Mechanical Properties of St37 Steel and 316L Stainless Steel Welded by the Friction Stir Welding Process
In this research, St37 and 316L steel sheets were welded using friction stir welding (FSW) process and effective parameters such as the rotational speed, linear speed of the tool, pin diameter, and their appropriate values were studied. The microstructure, hardness, and strength of the different welding regions were investigated. It was observed that in the stir zone (SZ), a mechanical operatio...
full textMy Resources
Journal title
volume 5 issue 1
pages 13- 29
publication date 2019-09
By following a journal you will be notified via email when a new issue of this journal is published.
No Keywords
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023