Developing a method for reliability allocation of series-parallel systems by considering common cause failure
Authors
Abstract:
Reliability allocation has an essential connection to design for reliability and is an important activity in the product design and development process. In determining the reliability of subsystems or components on the basis of goal reliability, attention must be paid to failure effect, failure information, and improvement opportunities based upon real potentials for reliability improvement. In the light of the fact that ignoring dependent failures inflicts irreversible damage on systems, and that redundant systems are vulnerable to Common Cause Failure (CCF) as well as independent failure, attention must be paid not only to components’ independent failure information, but also to CCF information in conducting reliability allocation for such systems. To consider improved failure rate alone cannot ensure the achievement of the goal reliability in question, because if the CCF occurrence exceeds a certain limit, the system’s reliability will certainly fail to match the goal reliability. This paper is an attempt to develop a method for reliability allocation of series-parallel systems by considering CCF, in such a way that potentials and priorities of reliability improvement are taken into consideration. The proposed method consists of four stages: 1) adding a series component to the redundant system in order to investigate CCF, 2) conducting reliability allocation for series components and the redundant system, 3) conducting reliability allocation for redundant system components, and 4) analyzing the failure rate of system components. The proposed method is run for water pumping systems and the results are evaluated. In this method, in addition to the improved failure rate of system components, the improved rate of CCF is computed, too. This proves instrumental and crucial for system designers in feasibility studies and conceptual design.
similar resources
A fuzzy reliability model for series-parallel systems
Fuzzy set based methods have been proved to be effective in handling many types of uncertainties in different fields, including reliability engineering. This paper presents a new approach on fuzzy reliability, based on the use of beta type distribution as membership function. Considering experts' ideas and by asking operators linguistic variables, a rule base is designed to determine the level ...
full textDeveloping a bi-objective optimization model for solving the availability allocation problem in repairable series–parallel systems by NSGA II
Bi-objective optimization of the availability allocation problem in a series–parallel system with repairable components is aimed in this paper. The two objectives of the problem are the availability of the system and the total cost of the system. Regarding the previous studies in series–parallel systems, the main contribution of this study is to expand the redundancy allocation problems to syst...
full textReliability Analysis of Three Elements Series and Parallel Systems under Time-varying Fuzzy Failure Rate
Reliability is the most important performance issue in the engineering design process but in the real world problems, there are limitations for using the conventional reliability. Fuzzy logic has proved to be effective in expressing uncertainties in different fields, including reliability engineering. In this paper, For both the series and parallel systems composed of three identical or differe...
full texta fuzzy reliability model for series-parallel systems
fuzzy set based methods have been proved to be effective in handling many types of uncertainties in different fields, including reliability engineering. this paper presents a new approach on fuzzy reliability, based on the use of beta type distribution as membership function. considering experts' ideas and by asking operators linguistic variables, a rule base is designed to determine the level ...
full textA Multi Objective Optimization Model for Redundancy Allocation Problems in Series-Parallel Systems with Repairable Components
The main goal in this paper is to propose an optimization model for determining the structure of a series-parallel system. Regarding the previous studies in series-parallel systems, the main contribution of this study is to expand the redundancy allocation parallel to systems that have repairable components. The considered optimization model has two objectives: maximizing the system mean time t...
full textRedundancy Allocation Combined with Supplier Selection for Design of Series-parallel Systems
In this paper a redundancy allocation problem is studied where for the first time the supplier selection is taken into consideration and redundant components are provided from appropriate suppliers with the most suitable offers such as discount on buying price of components, warranty length for components, things like that, so that the system reliability, profit and the warranty length proposed...
full textMy Resources
Journal title
volume 29 issue 2
pages 213- 230
publication date 2018-06
By following a journal you will be notified via email when a new issue of this journal is published.
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023