Corner Crack Effect on the Seismic Behavior of Steel Plate Shear Wall System

Authors

  • Mohsenali Shayanfar Department of Civil Eng, Faculty, Iran University of Science and Technology, Tehran, Iran
  • Vahid Broujerdian Department of Civil Eng, Faculty, Iran University of Science and Technology, Tehran, Iran
Abstract:

Although, experimental studies have reported fracture at the corner of Steel Plate Shear Walls (SPSW), no study has been performed to investigate the crack effect, yet. Therefore, in this paper, the effect of crack at the corner of SPSWs on the seismic behavior of the system was investigated. Two probable cracks, that have been studies at the corner of SPSWs utilizing extended Finite Element method based on cohesive crack approach, are initial horizontal crack and initial vertical crack. Numerical results indicated that small initial crack does not have considerable effect on the seismic behavior of SPSW. In addition, the horizontal crack is more effective than vertical crack. Since SPSWs with long initial horizontal crack are ruptured suddenly, so they could not be utilized as a lateral resisting in seismic zone. Nevertheless, no ruptures occur in SPSWs with vertical cracks. Therefore, SPSWs with horizontal crack must be repaired, but no repairing is needed in SPSWs with initial vertical cracks.

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

Seismic Performance of Steel Plate-Reinforced Concrete Composite Shear Wall

In tall buildings the reinforced concrete (RC) shear wall is one of the predominant structural components used to resist lateral loads induced by earthquakes around the world. Previous research demonstrated that shear walls displayed a sudden loss in lateral capacity due to the wall corner and web crushing in the plastic zone. In addition, it was found that large shear distortions in shear wall...

full text

Seismic Behavior of Intermediate Beams in Steel Plate Shear Walls

This paper presents some preliminary results of an ongoing research whose objective is to investigate the seismic behavior of intermediate beams (i.e., the beams other than those at the roof and foundation levels) in multi-story steel plate shear walls (SPSWs). Of primary interest is the determination of the strength level needed to avoid the formation of in-span plastic hinges, a relevant prac...

full text

Comparison of plasticity and stiffness of steel shear walls with composite steel plate shear wall

The steel shear wall and composite steel plate shear wall is introduced in recent three decade and is considered and is spread rapidly. Composite steel plate shear wall which is made of a layer of thin steel sheet with coating of reinforced concrete in one or both sides of steel palate is considered a third generation of resistance shear walls against lateral loads that in addition to increasin...

full text

Performance-Based Plastic Design of Moment Frame-Steel Plate Shear Wall as a Dual System

Steel Plate Shear Wall (SPSW) is an emerging seismic load-resistant system that, compared to other systems, enjoys the advantages of stable ductile behavior, fewer detailing requirements, rapid constructability, and economy. American seismic provisions decree that a SPSW should be designed as a moment frame with a web infill plate. Specifically, in case of buildings taller than 160 ft, it decre...

full text

SEISMIC OPTIMIZATION OF STEEL SHEAR WALL USING SHAPE MEMORY ALLOY

Nowadays, steel shear walls are used as efficient lateral-load-resistant systems due to their high lateral stiffness and carrying capacity. In this paper, the effect of substituting a shape memory alloy (SMA) material is investigated instead of using conventional steel in the shear wall. A numerical study is conducted using finite element method (FEM) by OpenSees software. For this purpose, at ...

full text

The Effect of Easy-Going Steel on KBF's Seismic Behavior

The knee bracing steel frame (KBF) is a new type of energy dissipating frame which enjoys exceptional ductility and lateral stiffness. Rather than the beam-column joint, one end of the diagonal brace in KBF is attached to the knee element. Indeed, the knee element as a hysteretic damper is designed and detailed to behave like a structural fuse by sustaining controlled inelastic deformations as ...

full text

My Resources

Save resource for easier access later

Save to my library Already added to my library

{@ msg_add @}


Journal title

volume 50  issue 2

pages  311- 332

publication date 2017-12-01

By following a journal you will be notified via email when a new issue of this journal is published.

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023