An investigation on Al6061/TiB2 nano composites production through Mechanical Alloying route and their corrosion behavior

Authors

  • Farhad Gharavi Department of Materials Engineering, Sirjan Branch, Islamic Azad University, Sirjan, Iran
  • G.H. Borhain Department of Materials Engineering, Malek-e-Ashtar University of Technology, Isfahan, Iran
  • Iman ebrahimzadeh 1Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
Abstract:

Aluminum-based alloy composites with high strength and low density can be used in corrosive environments. In this research, the nano-powders of A16061 alloy and A16061/TiB2 composite were synthesized by mechanical alloying (MA) method. Then, A16061 /TiB2 nano-composite bulk samples were prepared at laboratory scale by hot extrusion approach. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) devices were respectively used for measurement of particles and grains, and the polarization test was employed to assess the corrosion behavior of A16061 /TiB2 nano-composites. The grains size of hot extrusion samples were calculated as about 95 nm. Uniform corrosion behavior and pitting of the produced nano samples of MA6061 /1.25 TiB2 have higher corrosion resistance compared to the alloy samples of MA6061.3. The uniform corrosion in the 2MA-Al-6061/1.25TiB2 composite had the lowest rate compared to other samples.The sensitivity of this alloy to pitting corrosion has raised compared to the melting state; however, this sensitivity is less than the alloy made by mechanical alloying method.

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

A comparison study of polymer/cobalt ferrite nano-composites synthesized by mechanical alloying route

In this research, the effect of different biopolymers such as polyethylene glycol (PEG) and polyvinylalcohol (PVA) on synthesis and characterization of polymer/cobalt ferrite (CF) nano-composites bymechanical alloying method has been systematically investigated. The structural, morphological andmagnetic properties changes during mechanical milling were investigated by X-ray diffraction (XRD),Fo...

full text

a comparison study of polymer/cobalt ferrite nano-composites synthesized by mechanical alloying route

in this research, the effect of different biopolymers such as polyethylene glycol (peg) and polyvinylalcohol (pva) on synthesis and characterization of polymer/cobalt ferrite (cf) nano-composites bymechanical alloying method has been systematically investigated. the structural, morphological andmagnetic properties changes during mechanical milling were investigated by x-ray diffraction (xrd),fo...

full text

AN INVESTIGATION ON REACTIVE SINTERING OF NANO-CRYSTALLINE TiO2 -Al POWDER PREPARED BY MECHANICAL ALLOYING

In this research an ultra-fine grained composite structure consisting of an intermetallic matrix together with dispersed nano-sized Al2O3 obtained via mechanical activation of TiO2 and Al in a high energy ball mill and sintering of consolidated samples. Phase composition and morphology of the milled and sintered samples were evaluated by XRD and SEM techniques Thermal behavior of the powder sa...

full text

Production and Characterization of Nano Crystalline Fe85Si10Ni5 Soft Magnetic Alloys by Mechanical Alloying

Abstract There are various methods to produce iron based nano crystalline magnetic alloys. Among these methods, mechanical alloying is one of the most important. In this research, nano crystalline Fe85Si10Ni5 soft magnetic alloy was synthesized by mechanical alloying. The effect of alloying time on phase constituents and magnetic properties of the produced powders was investigated, by X-ray di...

full text

Improved mechanical performance and delayed corrosion phenomena in biodegradable Mg-Zn-Ca alloys through Pd-alloying.

The influence of partial substitution of Mg by Pd on the microstructure, mechanical properties and corrosion behaviour of Mg(72-x)Zn(23)Ca(5)Pd(x) (x=0, 2 and 6 at.%) alloys, synthesized by copper mould casting, is investigated. While the Mg(72)Zn(23)Ca(5) alloy is mainly amorphous, the addition of Pd decreases the glass-forming ability, thus favouring the formation of crystalline phases. From ...

full text

My Resources

Save resource for easier access later

Save to my library Already added to my library

{@ msg_add @}


Journal title

volume 6  issue 2

pages  72- 82

publication date 2018-06-01

By following a journal you will be notified via email when a new issue of this journal is published.

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023