microstructure and mechanical properties of the friction welded joint between x53crmnnin219 and x45crsi93 stainless steel

Authors

khalil gheisari

department of materials science and engineering, faculty of engineering, shahid chamran university, ahvaz, iran mohammad reza abasi

department of materials science and engineering, faculty of engineering, shahid chamran university of ahvaz, ahvaz, iran

abstract

dissimilar metals friction welding of austenitic–martensitic stainless steels is commonly used in order to manufacture engine valves in the automobile industry. in this study, x53crmnnin219 (austenitic stainless steel) and x45crsi93 (martensitic stainless steel) valve steel rods were welded by friction welding process. the welded joint was then heat treated at 760 0c for 60 min. mechanical properties of the welded and heat treated samples were identified by means of microhardness and tensile tests. the microstructure of the weld and the fracture surface of the tension samples were investigated by optical microscopy and scanning electron microscopy. fractographic evaluations also were performed by using scanning electron microscopy. according to the findings, due to the higher thermal conductivity and lower strength of the martensitic stainless steel, a larger upset and a broader heat affected zone is observed in the martensitic side. furthermore, formation of non-tempered martensite with the maximum hardness of 880 hv in the heat affected zone (haz) of the martensitic stainless steel side makes as-welded material susceptible to brittle fracture as detected by fractographic examinations. nevertheless, a successfully transition from brittle to ductile behavior is observed by the post-weld heat treatment at 760 0c for 60 min.

Upgrade to premium to download articles

Sign up to access the full text

Already have an account?login

similar resources

Microstructure and Mechanical Properties of the Friction Welded Joint between X53CrMnNiN219 and X45CrSi93 Stainless Steel

Dissimilar metals friction welding of austenitic–martensitic stainless steels is commonly used in order to manufacture engine valves in the automobile industry. In this study, X53CrMnNiN219 (austenitic stainless steel) and X45CrSi93 (martensitic stainless steel) valve steel rods were welded by friction welding process. The welded joint was then heat treated at 760 0C for 60 min. Mechanical prop...

full text

Evaluation of microstructure and mechanical properties of friction stir welded copper / 316L stainless steel dissimilar metals

In the present research, friction stir welding (FSW) process was used for butt joining of pure copper plate to 316L stainless steel plate. Mechanical properties and microstructural characteristics of the joint were evaluated by microhardness and tensile tests as well as optical and scanning electron microscope (SEM). It was found that microstructure of the weld nugget (WN) has fine grains where...

full text

evaluation of microstructure and mechanical properties of friction stir welded copper / 316l stainless steel dissimilar metals

in the present research, friction stir welding (fsw) process was used for butt joining of pure copper plate to 316l stainless steel plate. mechanical properties and microstructural characteristics of the joint were evaluated by microhardness and tensile tests as well as optical and scanning electron microscope (sem). it was found that microstructure of the weld nugget (wn) has fine grains where...

full text

Effects of Friction Stir Processing on the Microstructure and Mechanical Properties of Fusion Welded 304L Stainless Steel

A variation of FSW, friction stir processing (FSP), has been used to modify selected regions of materials to enhance specific properties while eliminating fusion welding defects such as porosity, cracking, and the cast microstructure. The combination of fusion welding defects and high tensile residual stresses caused by the solidification of the molten weld pool adversely affect the post weld s...

full text

The Effect of Friction Stir Processing Speed Ratio on the Microstructure and Mechanical Properties of A 430 Ferritic Stainless Steel

This study is an attempt to investigate the effect of welding rotational and traverse speed on mechanical and microstructural properties of A 430 stainless steel in order to give an effective processing window to achieve an appropriate microstructure and so mechanical properties. There are a wide range industrial uses for ferritic stainless steel. There from they have some problems like grain c...

full text

Effect of Welding Parameters in the Microstructure and Mechanical Properties of Friction-Welded Joints of 100Cr6 Steel

 In this study, high-carbon, chromium alloy steel (100Cr6) having the initial spheroidized microstructure was welded using the rotary friction welding method. The effects of process parameters such as friction time and friction force were experimentally investigated. The friction welded joints were produced of two 100Cr6 steel rods. In order to examine the microstructure and mechanical properti...

full text

My Resources

Save resource for easier access later


Journal title:
journal of advanced materials and processing

جلد ۵، شماره ۱، صفحات ۸۱-۹۲

Hosted on Doprax cloud platform doprax.com

copyright © 2015-2023