settlement analysis of embankment with finite element method
Authors
abstract
it is correct control and monitoring of modern embankment dams that are very vital in the geotechniqual constructions. the improvement of methods of stability control, using the effective stress and the measurement of ganglionic water pressure in embankment dams cause more the safety for this kind of dams. nowedays there is such an idea that in stead of using of being safety factor against coast, designments must be done according to acceptable displacement. analytic appraoach is using the finite element that is capable of fortelling the displacement parameters. monitoring of dams with setting up accurate tools in the sensitive points and measurement various parameters such as pore water pressure and displacement points and measurement various parameters such as pore water pressure and displacement more or most common settlement and movement is possible. the displacement that occur all of a sudden at the end of this process can indicate be causes of enlargement of strain inside the dam body. this is the reason of undesirable decreasing of stresses or causes the start of an increasing impairment. by investigation of datas and using inverted analysis about the very unusual condition of mahabad dam, it has been tried to define the cause of this action in this thesis. from the start of construction an unnatural settlement and horizontal movement has occurred in it. during the construction 130 cm and during the exploitation 60 cm settlement has occurred in the foundation up to now. also from the end of construction the maximum settlement and vertical movement are 150 cm and 100 cm respectively. in this paper monitoring of dams mahabad with using acculate tools information and numerical analytic has consideratd. in performing numerical analytic from plaxis using finite element program. after construction cutoff walls and finishing operation injection in foundation of dam, rate of seepage from foundation is decreased and is according to numerical calculations in negligible extent and rate of seepage in body dam.
similar resources
Embankment basal stability analysis using shear strength reduction finite element method
The stability evaluation of the slope commonly uses limit equilibrium methods, for example, Fellenius’ method in Japan. The limit equilibrium methods have two limitations. (1) It is necessary to divide the sliding mass into slices, and to set up some additional equations to make the problem statically determinate. (2) It is necessary to search sliding surface with a minimum safety factor. Shear...
full textNumerical analysis of embankment dam monitoring during construction of the finite element method with software SIGMA / W (Case study: dam Kaboodval)
In this research in numerical analysis software packages SIGMA / W based on the finite element method was to have been used. For this purpose, during the construction of the dam Kaboodval using behavioral models elastic - plastic and elastic non-homogeneous, non-linear elastic, linear elastic been analyzed and pore pressure, stresses in the body and its meeting with the Data Tools the compariso...
full textAnalysis of non-connected piled raft foundations (NCPRF) with cushion by finite element method
For the optimum design of Piled Raft Foundations (PRF), the concept of settlement reducer piles has been applied. However, when these piles are connected to the raft, a high stress may develop in the relatively small number of piles. Therefore, an alternative approach is to disconnect the piles from the raft forming a new system called a non-connected or disconnected piled-raft foundation (NCPR...
full textAnalysis of Thin-Walled Steel Sections Filled with Concrete Using Non-Linear Finite Element Method
Being economical and performing well under cyclic loads, steel sections filled with concrete have been widely used in structural buildings. Extensive studies and experiments have been conducted to investigate the influence of different parameters and loadings on the behavior of these structural components. Based on the data available from previous experiments and studies, this paper discusses t...
full textAnalysis of Thin-Walled Steel Sections Filled with Concrete Using Non-Linear Finite Element Method
Being economical and performing well under cyclic loads, steel sections filled with concrete have been widely used in structural buildings. Extensive studies and experiments have been conducted to investigate the influence of different parameters and loadings on the behavior of these structural components. Based on the data available from previous experiments and studies, this paper discusses t...
full textFracture Mechanics Analysis of Fourth Lumbar Vertebra in Method of Finite Element Analysis
Objective: In this paper, finite element model of the L4 vertebra subjected to combination of compression and flexion loading in isotropic and anisotropic cases is investigated. Methods: In both cases, the vertebra is considered homogeneous. Also, the body of vertebra is divided to cancellous and cortical sections in anisotropic model, but the process is assumed isotropic such as isotropic mode...
full textMy Resources
Save resource for easier access later
Journal title:
مهندسی سازهجلد ۴، شماره ۵، صفحات ۵۳-۶۱
Hosted on Doprax cloud platform doprax.com
copyright © 2015-2023