Screw-shaped Contaminant of Distilled Water.

نویسنده

  • A L HOUWINK
چکیده

FIG. 9. Direct contact photography of Armillaria mellea hyphae by its own light. Kodak Microfile, 3-hr exposure. Negative photomicrographed; figutre constitutes a negative print. Arrows indicate clamp connections. X 1,200. FIG. 10. Direct contact photography of Armillaria mellea by its own light. Polaroid Type 55 P/N filn, 30-min exposure. Negative photomicrographed on Microfile film, figuire constitutes a negative print. X 1,000. for successful exposures with Microfile or Adox KB21. Thereafter, either the agar dried up or the emulsion peeled off the film backing. With the Polaroid film, where unfortunately the grain is less even, a 1-hr exposure was sufficient. After the film was processed, the exposed areas were examined microscopically. The growth pattern and mycelial distribution of the edge of a growing culture where the hyphae are distinct, separate, and in one layer were clearly duplicated in the emulsion grain. Figures 9, 10, and 11 show the amount of detail observable. The negatives were then photomicrographed with Microfile film and the pictures enlarged when printed. In Fig. 9 the arrows indicate clamp connections, and in Fig. 11 the branching pattern is readily evident. Finer structural details cannot be made out, and it remains to find an emulsion of equivalent speed, but with considerably smaller even grains, before the area of light emission within the cell can be determined. For the present, it appears that light emission occurs throughout the cell.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Experimental Investigation of Heat Transfer Enhancement in a Finned U-Shaped Heat Pipe of CPU Cooling System Using Different Fluids

This paper experimentally studies the heat absorption performance of a heat sink with vertical embedded heat pipes in the aluminum blade. The cooling system with embedded heat pipes distributes heat from the CPU to both the base plate and the heat pipes, and then transfer heat from fins to the Environment. The thermal resistance and heat transfer coefficient are evaluated for natural convection...

متن کامل

Simple Experiment Showing the Existence of "liquid Water" Film on the Ice Surface 1

Two small ice spheres are suspended by thin cotton filaments. The top of one filament is displaced horizontally by a screw motion. The movable ice sphere is brought in contact with the stationary sphere, and then the screw is turned back. The normal cohesion is measured by the inclination of the filament when the spheres are separated. Sometimes the ice spheres showed a rotation before separati...

متن کامل

Presence of nonylphenols in plastic films and their migration into food simulants.

Nonylphenols (NP) possess estrogenic activities and may cause increased risk of cancerous and reproductive abnormalities in several living organisms. Despite their harmful nature, NPs are used as additives in food packaging material, especially plastic, which is the main food contact material in today's packaging landscape. According to the fact that food packaging is one of the major potential...

متن کامل

Kinetics of the Swelling of Cells and Tissues

The rate of swelling of Arbacia eggs in dilute sea water, studied by Lillie and by Lucke and McCutcheon, may be expressed by the formulae derived for the rate of increase in volume of a solution enclosed in a collodion sac. The rate of swelling of slices of carrot in distilled water, measured by Stiles and Jørgensen, may be expressed by the equation derived previously for the swelling of simila...

متن کامل

3D Printing by Fused Deposition Modeling of Capsular Devices for Oral Pulsatile Release Based on Swellable/Erodible Polymers

Swellable/Erodible Polymers A. Melocchi , F. Parietti , F. Casati , A. Maroni , A. Gazzaniga , L. Zema 1 1 Universita Degli Studi di Milano, 2 Massachusetts Institute of Technology Purpose To prepare swellable/erodible capsular devices for oral pulsatile release via 3D printing by Fused Deposition Modeling (FDM), starting from in-house produced filaments based on hydroxypropyl cellulose (HPC), ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of bacteriology

دوره 86  شماره 

صفحات  -

تاریخ انتشار 1963