Study of Ionic Conductivity Profiles of the Air Cathode of a PEMFC by AC Impedance Spectroscopy

نویسندگان

  • Qingzhi Guo
  • Maria Cayetano
  • Yu-min Tsou
  • Emory S. De Castro
  • Ralph E. White
چکیده

A characterization of the ionic conduction of the active layer of a polymer electrolyte membrane fuel cell ~PEMFC! cathode by ac impedance measurement at open-circuit potential conditions was conducted. Porous electrode theory was used to derive a compact equation, ]2F& 2 /]y 1 ] ln f(y)/]y 3 ]F& 2 /]y 2 R/ f (y)(1 1 jV)F& 2 5 0, to solve for the impedance response of a cathode at open-circuit potential conditions. This equation includes a parameter R, the ratio of an ionic resistance ~evaluated at the active layer/membrane interface!, to the total charge-transfer resistance of the active layer. The influence of an assumed ionic conductivity distribution profile f (y) on the error in the estimation of total double-layer capacitance of the active layer from the 21/(Z Imv) vs. ZRe plot was also investigated in this work. The increase of ionic conductivity in the active layer of an air cathode with an increase in the ionomer loading was revealed from both impedance data and surface area measurements. A nonlinear parameter estimation method was used to extract the ionic resistance from the high-frequency region of the impedance data at open-circuit potential conditions. The assumed ionic conductivity distribution profile in the active layer was found to vary with ionomer loadings. © 2003 The Electrochemical Society. @DOI: 10.1149/1.1612502# All rights reserved.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Development and Simulation of a PEM Fuel Cell model for Prediction of Water Content and Power Generation

The proton exchange membrane (PEMFC) fuel cell represents the energy of the future, in parallel with hydrogen. However, this technology must meet many technical challenges related to performance and durability before being sold on a large scale. It is well known that these challenges are closely linked to water management. This paper develops and implements a model of PEM fuel for simulation to...

متن کامل

Preparation and Physical Characterization of Sulfonated Poly (Ether Ether Ketone) and Polypyrrole Composite Membrane

Sulfoanted poly(ether ether ketone) membranes were prepared by the sulfonating agent sulfuric acid. These membranes were modifed by incorporating conducting polymer polypyrrole in order to increase the ionic conductivity and reduce the methanol transmission rate. The modifed composite membranes were then compared on the basis of ionic conductivity, methanol transmission...

متن کامل

Investigations on structural, optical, and AC conductivity of Polyaniline/Manganese Dioxide nanocomposites

A Polyaniline/Manganese dioxide (PANI/MnO2) nanocomposite contains five weight percentages of MnO2. It has been successfully prepared by in situ polymerization. The structural, optical, and conductivity of nanocomposites remain relative to changes with respect to the weight percentage of MnO2. The structural, morphological, optical, and electrical conductivity i...

متن کامل

Assessment of the Effects of Flow Rate and Ionic Strength on the Performance of an Air-Cathode Microbial Fuel Cell Using Electrochemical Impedance Spectroscopy

Impedance changes of the anode, cathode and solution were examined for an air-cathode microbial fuel cell (MFC) under varying conditions. An MFC inoculated with a pre-enriched microbial culture resulted in a startup time of less than ten days. Over this period, the anode impedance decreased below the cathode impedance, suggesting a cathode-limited power output. Increasing the anode flow rate di...

متن کامل

Preparation, characterization and stability of Li-ion conducting Li1.5Al0.5Ge1.5(PO4)3 glass-ceramic with NASICON-type structure

A conducting lithium aluminum germanium phosphate (LAGP) glass-ceramic with a formula of Li1.5Al0.5Ge1.5(PO4)3 was synthesized by melt-quenching method and subsequent crystallization at 850 °C for 8 h. The prepared glass-ceramic was characterized using differential scanning calorimetry (DSC), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and AC impedance techniqu...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2003