THE AGE-PRECIPITATIONS STRUCTURE OF Al-Mg-Ge ALLOY AGED AT 473K UMACNIANIE WYDZIELENIOWE STOPU Z Al-Mg-Ge PO STARZENIU W 473K
نویسندگان
چکیده
The Al-Mg-Ge alloy is one of the age-hardening aluminum alloy after solution heat treatment. It has been proposed that the age-precipitation behavior of Al-Mg-Ge alloy is different from that of Al-Mg-Si alloy according to our previous works about the microstructure on Al-Mg-Ge alloy over-aged at 523K. For example, The hardness of peak aged Al-1.0mass%Mg2Ge alloy is higher than that of Al-1.0mass%Mg2Si alloy.The precipitates in the over-aged samples have been classified as some metastable phases, such as the β’-phase and Type-A precipitates and equilibrium phase of β-Mg2Ge by TEM observation.There a few reports about microstructure on Al-Mg-Ge alloys observed by TEM for different aging times. The age-precipitations structure of Al-Mg-Ge alloy has not been became clear. In this work, TEM observation was investigated the microstructure on Al-1.0mass%Mg2Ge alloy for difference aging times aged at 473K.
منابع مشابه
Microstructure Stability and Creep Strength in a Die-Cast AX52 Magnesium Alloy
Superior creep strength of a heat resistant AX52 magnesium alloy is ascribed to the grain boundary eutectic Al2Ca phase covering the primary -Mg grains. The eutectic phase is stable in morphology at temperatures below 473K, while it collapses during long term exposure at temperatures higher than 473K. The microstructural change of the alloy during high temperature exposure is characterized by t...
متن کاملTHERMAL ANALYSIS AND KINETICS OF THE PRECIPITATION IN WROUGHT Al-Mg, Al-Mg-ScAND Al-Mg-Sc-Me (Me=Zr, Ti) ALLOYS
Precipitation behaviour of wrought Al-6Mg alloys with ternary scandium and quaternary zirconium and titanium has been studied. Hardness measurements and resistivity studies are employed to assess the precipitation behaviour of scandium doped Al-6Mg alloy without or with quaternary additions of zirconium and titanium. Further, the kinetics of precipitations are studied by differential scanning c...
متن کاملFRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY
The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were ...
متن کاملEffects of Various Ageing Heat Treatments on Microstructural Features and Hardness of Piston Aluminum Alloy
Piston aluminum alloys have different intermetallic phases, such as Cu3Al, Mg2Si ,and AlNi phases. The morphology and the distribution of such phases have important roles on mechanical properties of the piston material. Therefore, in this research, various ageing heat treatments on the mentioned material were done and the microstructural feature and the hardness were studi...
متن کاملEffect of Dynamic Strain Aging on Isothermal (473K) Low Cycle Fatigue of Ferritic Ductile Cast Iron
The ferritic ductile iron (FCD400) is widely used as industrial material. As regards to its high temperature application, fatigue at elevated temperature, and advanced mechanical properties has been investigated and clarified. In low cycle fatigue (LCF), the S-N curve is presented by the relation of plastic strain to the number of cycles as fatigue life, which can be predicted by the Manson-Cof...
متن کامل