Pneumatic Performance Study of a High Pressure Ejection Device Based on Real Specific Energy and Specific Enthalpy

نویسندگان

  • Jie Ren
  • Fengbo Yang
  • Dawei Ma
  • Guigao Le
  • Jianlin Zhong
چکیده

In high-pressure dynamic thermodynamic processes, the pressure is much higher than the air critical pressure, and the temperature can deviate significantly from the Boyle temperature. In such situations, the thermo-physical properties and pneumatic performance can’t be described accurately by the ideal gas law. This paper proposes an approach to evaluate the pneumatic performance of a high-pressure air catapult launch system, in which esidual functions are used to compensate the thermal physical property uncertainties of caused by real gas effects. Compared with the Nelson-Obert generalized compressibility charts, the precision of the improved virial equation of state is better than Soave-Redlich-Kwong (S-R-K) and Peng-Robinson (P-R) equations for high pressure air. In this paper, the improved virial equation of state is further used to establish a compressibility factor database which is applied to evaluate real gas effects. The specific residual thermodynamic energy and specific residual enthalpy of the high-pressure air are also derived using the modified corresponding state equation and improved virial equation of state which are truncated to the third virial coefficient. The pneumatic equations are established on the basis of the derived residual functions. The comparison of the numerical results shows that the real gas effects are strong, and the pneumatic performance analysis indicates that the real dynamic thermodynamic process is obviously different from the ideal one.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Experimental Assessment of a Fixed On-Shore Oscillating Water Column Device: Case Study on Oman Sea

Ocean wave is one of the renewable energy resources that these days various devices are used to extract its energy. Oscillating Water Column (OWC) installed on the shore is one of the wave energy absorption systems which has received attention due to its simple structure. Investigation of the pneumatic power is of great importance in such systems as the conversion of wave energy to pneumatic en...

متن کامل

Design and Experimental Study of a Combined Pneumatic Plot Seed-metering Device for Cotton

This study presents a combined pneumatic seed-metering device (SMD) that could not only fill, carry, and meter seeds, but also switch quickly between seed-metering and seed-cleaning modes, and clean seeds thoroughly and rapidly. The seed-filling, seed-carrying, and seed-metering modes of the SMD were analyzed based on a theoretical kinematic model. Furthermore, a three-factor, three-level ortho...

متن کامل

Transient Two-Dimensional (r-z) Cyclic Charging/Discharging Analysis of Space Thermal Energy Storage Systems (RESEARCH NOTE)

A two-dimensional transient axi-symmetric model was developed to study the effects of various thermal and geometric parameters on cyclic heating and cooling modes of a phase-change thermal energy storage system. The high-temperature thermal energy storage device utilizes LiH for heat sink applications to store the waste heat generated during power-burst periods. The stored heat is then discharg...

متن کامل

2. British Petroleum (BP), “BP energy outlook 2035”, 2014 (January)

In recent years, many efforts have been made to reduce pollution in compression ignition engines. Dimethyl ether is one of the methods to achieve this goal due to its special properties such as high Cetane number and low pollution. Also, one of the parameters that plays an important role in improving combustion and engine performance is fuel injection pressure. In the present study, a numerical...

متن کامل

Computational Investigation of the Efference of Different Fullerenes on Aktogen High Energy

In this research, HMX energy derivatives with different carbon-containing fullerenes in different temperature conditions were studied using density functional theory. For this purpose, the materials were first geometric optimized, then the thermodynamic parameters were calculated for all of them. Then, the process of changing the energy-dependent parameters such as specific heat capacity, entha...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Entropy

دوره 16  شماره 

صفحات  -

تاریخ انتشار 2014