Does the femur roll-back with flexion?
نویسندگان
چکیده
MRI studies of the knee were performed at intervals between full extension and 120 degrees of flexion in six cadavers and also non-weight-bearing and weight-bearing in five volunteers. At each interval sagittal images were obtained through both compartments on which the position of the femoral condyle, identified by the centre of its posterior circular surface which is termed the flexion facet centre (FFC), and the point of closest approximation between the femoral and tibial subchondral plates, the contact point (CP), were identified relative to the posterior tibial cortex. The movements of the CP and FFC were essentially the same in the three groups but in all three the medial differed from the lateral compartment and the movement of the FFC differed from that of the CR Medially from 30 degrees to 120 degrees the FFC and CP coincided and did not move anteroposteriorly. From 30 degrees to 0 degrees the anteroposterior position of the FFC remained unchanged but the CP moved forwards by about 15 mm. Laterally, the FFC and the CP moved backwards together by about 15 mm from 20 degrees to 120 degrees. From 20 degrees to full extension both the FFC and CP moved forwards, but the latter moved more than the former. The differences between the movements of the FFC and the CP could be explained by the sagittal shapes of the bones, especially anteriorly. The term 'roll-back' can be applied to solid bodies, e.g. the condyles, but not to areas. The lateral femoral condyle does roll-back with flexion but the medial does not, i.e. the femur rotates externally around a medial centre. By contrast, both the medial and lateral contact points move back, roughly in parallel, from 0 degrees to 120 degrees but they cannot 'roll'. Femoral roll-back with flexion, usually imagined as backward rolling of both condyles, does not occur.
منابع مشابه
Can a total knee arthroplasty be both rotationally unconstrained and anteroposteriorly stabilised?
OBJECTIVES Throughout the 20th Century, it has been postulated that the knee moves on the basis of a four-bar link mechanism composed of the cruciate ligaments, the femur and the tibia. As a consequence, the femur has been thought to roll back with flexion, and total knee arthroplasty (TKA) prostheses have been designed on this basis. Recent work, however, has proposed that at a position of bet...
متن کاملTibiofemoral movement 1: the shapes and relative movements of the femur and tibia in the unloaded cadaver knee.
In six unloaded cadaver knees we used MRI to determine the shapes of the articular surfaces and their relative movements. These were confirmed by dissection. Medially, the femoral condyle in sagittal section is composed of the arcs of two circles and that of the tibia of two angled flats. The anterior facets articulate in extension. At about 20 degrees the femur 'rocks' to articulate through th...
متن کاملReliability of Measuring Lumbar Lordosis, Flexion and Extension Using Dual Inclinometer in Healthy Subjects and Patients with Non-Specific Chronic Low Back Pain
Objective: Accurate assessment of lumbar range of motion is of great value for both evaluating lumbar functions and monitoring treatment progress. Recent research indicates that there is no general consensus on the most valid and reliable method of measuring spinal range of motion. The purpose of this study was to determine the intra-rater reliability of lumbar flexion and extension measurement...
متن کاملFemoral Roll Back in Total Knee Arthroplasty: Comparison between Prostheses That Preserve and Sacrifice the Posterior Cruciate Ligament
UNLABELLED To compare the rollback of the contact point between the femoral component and the tibial polyethylene as the knee is flexed, in two types of total knee arthroplasty: one that sacrifices and the other that preserves the posterior cruciate ligament (PCL). METHODS Under fluoroscopy, 36 knees from 32 patients who underwent total knee arthroplasty were evaluated. Using lateral images, ...
متن کاملAnalytical and Numerical Investigation of Four-roll Bending
Four-roll bending process is usually used for manufacturing of seamed thick-walled and thin-walled cylinders. Due to complexity of this process, the analytical solution of plate bending in this process has not been developed completely. The existence of friction and multi-step processing makes it more difficult. Investigation of four-roll bending process using analytical and numerical methods i...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- The Journal of bone and joint surgery. British volume
دوره 86 6 شماره
صفحات -
تاریخ انتشار 2004