Electromagnetic Rotary Tables for Mill and Drill Machining

نویسنده

  • MARIO STAMANN
چکیده

MARIO STAMANN Otto von Guericke University Chair of Electrical Drive Systems Universitätsplatz 2 39106 Magdeburg GERMANY [email protected] THOMAS SCHALLSCHMIDT Otto von Guericke University Chair of Electrical Drive Systems Universitätsplatz 2 39106 Magdeburg GERMANY [email protected] ROBERTO LEIDHOLD Otto von Guericke University Chair of Electrical Drive Systems Universitätsplatz 2 39106 Magdeburg GERMANY [email protected]

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Development of Design and Manufacturing Support Tool for Optimization of Ultrasonic Machining (USM) and Rotary USM

Ultrasonic machining (USM) is a mechanical material removal process used to erode holes and cavities in hard or brittle work pieces by using shaped tools, high-frequency and an abrasive slurry. This paper addresses the concept and development of an expert system (ES) for hard and brittle material, such as glass, quartz, diamond, carbides, semi conducting materials, ceramic and graphite which ca...

متن کامل

Development of Design and Manufacturing Support Tool for Optimization of Ultrasonic Machining (USM) and Rotary USM

Ultrasonic machining (USM) is a mechanical material removal process used to erode holes and cavities in hard or brittle work pieces by using shaped tools, high-frequency and an abrasive slurry. This paper addresses the concept and development of an expert system (ES) for hard and brittle material, such as glass, quartz, diamond, carbides, semi conducting materials, ceramic and graphite which ca...

متن کامل

Surface roughness in rotary ultrasonic machining: hypotheses and their testing via experiments and simulations

Rotary ultrasonic machining (RUM) is a nontraditional drilling process. It has been used to drill not only brittle but also ductile materials. It was observed that the surface roughness of the drilled hole near the entrance side was better than that near the exit side. However, explanations about this observation could not be found in the literature. This paper aims to provide explanations abou...

متن کامل

Mechanical Surface Treatments of Ti-6Al-4V Miniplate Implant Manufactured by Electrical Discharge Machining (TECHNICAL NOTE)

Present work aims at multi-mechanical surface treatment of Ti-6Al-4V based-miniplate implant manufactured by electrical discharge machining (EDM) for biomedical use. Mechanical surface treatment consists of consequent use of ultrasonic cleaning, rotary tumbler polishing, and brushing. Surface layers are analyzed employing scanning electron microscopy and energy dispersive X-ray spectroscopy. Al...

متن کامل

Design, Manufacturing and Surface quality Analysis of Machining by Self-Rotary Milling Tool

One of the disadvantages of conventional milling tools is to produce a large amount of heat in cutting zone and so making the tool warmer. As a result, the tool would be worn and its life time would be reduced. Therefore, in long time machining, it is essential to change inserts and tools, continiously. A milling tool with self rotary cutting inserts was designed and manufactured that enables i...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2014