A low diffraction laser beam as applied to polymer ablation

نویسندگان

  • Xuanhui Lu
  • Y. Lawrence Yao
  • Kai Chen
چکیده

A low diffraction beam is obtained by altering the existing resonator of a CO2 laser using a special phase plate. The phase plate is designed based on the boundary diffraction principle and is implemented on the resonator rear mirror. It is found that the low diffraction beam has a smaller M 2 value than that of a Gaussian beam. The effects of the improved beam quality on a laser ablation process are investigated using a polymeric material. A theoretical model is provided to predict the laser ablated hole profile and penetration depth. The theoretical results are in agreement with the experimental measurements. Both the experimental and theoretical results show that the low diffraction beam has marked advantages over the Gaussian beam in ablation-dominated material removal processes in terms of larger depth and smaller taper at the same average power level. © 2001 Laser Institute of America.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Ultrafast large-area micropattern generation in nonabsorbing polymer thin films by pulsed laser diffraction.

An ultrafast, parallel, and beyond-the-master micropatterning technique for ultrathin (30-400 nm) nonabsorbing polymer films by diffraction of laser light through a 2D periodic aperture is reported. The redistribution of laser energy absorbed by the substrate causes self-organization of polymer thin films in the form of wrinklelike surface relief structures caused by localized melting and freez...

متن کامل

بررسی برهمکنش لیزر Er,Cr:YSGG با بافت سخت دندان

Background and Aims: Nowadays lasers are used as alternatives to the tooth preparation because of reducing pain, bloodshed and stress. The aim of this study was to observe the effect of Er,Cr:YSGG laser on the dental hard tissues. Materials and Methods: For this studty, molar teeth with no caries or dental restoration and enamel cracks were used. The laser power were taken from 0.5, 1, 1.5, ...

متن کامل

On the angular dependence of focused laser ablation by nanosecond pulses in solgel and polymer materials

Focused laser ablation by single laser pulses at varying angles of incidence is studied in two materials of interest: a solgel ~Ormocer 4! and a polymer ~SU8!. For a range of angles ~up to 70° from normal!, and for low-energy ~,20 mJ!, 40 ns pulses at 266 nm wavelength, the ablation depth along the direction of the incident laser beam is found to be independent of the angle of incidence. This a...

متن کامل

Laser Micro-Machining of Spherical and Elliptical 3-D Objects using Hole Area Modulation Method

Laser micromachining has the capability to fabricate very small and basic 2.5 D geometric features on a range of materials in the form of laser ablation or irradiation. Short pulsed lasers that can achieve wide range of wavelengths in the form of harmonics of infrared laser beam at 1064 nm wavelength have been a very effective micro-machining tool used for hole drilling, cutting, scribing, trim...

متن کامل

Investigation of the ultrasonic welding strength in glass fiber reinforced thermoset polymers with surface preparation method using laser beam

In this research, tensile strength of ultrasonic welded parts made of thermoset polymer-reinforced glass fiber with surface preparation has been investiagted. In order to elevate the adhesion of two surfaces laser grooving method has been applied. Two type of thermoplastic materials including Plymethyl methacrylate (PMMA) and polypropylene (PP) have been used as interlayers. Influences of main ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2001