Spatial separation of cavitating bubble populations: the nanodroplet injection model.

نویسندگان

  • Hangxun Xu
  • Nathan C Eddingsaas
  • Kenneth S Suslick
چکیده

Intense Na* emission was observed from 0.1 M Na(2)SO(4) in 95% sulfuric acid during multibubble sonoluminescence (MBSL). As a function of acoustic intensity, three different morphologies are observed for the cloud of light emitting bubbles. Even more strikingly, there is a spatial separation between blue-white emitting bubbles and orange emitting bubbles, easily observed by the naked eye. Surprisingly, no Na* emission was observed on the top of a bubble cloud (blue-white emission) while strong Na* emission predominates at the bottom. This observation provides the first experimental evidence to distinguish between the two types of two-site models of acoustic cavitation and MBSL: spatial separation of emission from nonvolatiles (e.g., Na*) ought not to be observed for the heated-shell model but is predicted from the injected droplet model.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Numerical Simulation of Separation Bubble on Elliptic Cylinders Using Three-equation k-? Turbulence Model

Occurrence of laminar separation bubbles on solid walls of an elliptic cylinder has been simulated using a recently developed transitional model for boundary layer flows. Computational method is based on the solution of the Reynolds averaged Navier-Stokes (RANS) equations and the eddy-viscosity concept. Transitional model tries to simulate streamwise fluctuations, induced by freestream turbulen...

متن کامل

Effect of Injection Pressure and Size of Nozzle Throat of a Cavitating Jet on Cavitation Peening

Abstract Cavitation peening is a peening method using impacts at cavitation bubble collapses generated by a cavitating jet. In order to introduce compressive residual stress avoiding damage on the peened surface, residual stress of stainless steel was investigated at various cavitating conditions. It was revealed that the large cavitating jet at low injection pressure such as 30 MPa can introdu...

متن کامل

Study of Parameters Affecting Separation Bubble Size in High Speed Flows using k-ω Turbulence Model

Shock waves generated at different parts of vehicle interact with the boundary layer over the surface at high Mach flows. The adverse pressure gradient across strong shock wave causes the flow to separate and peak loads are generated at separation and reattachment points. The size of separation bubble in the shock boundary layer interaction flows depends on various parameters. Reynolds-averaged...

متن کامل

Numerical Study of Bubble Separation and Motion Using Lattice Boltzmann Method

In present paper acombination of three-dimensional isothermal and two-dimensional non-isothermal Lattice Boltzmann Method have been used to simulate the motion of bubble and effect of wetting properties of the surface on bubble separation. By combining these models, three-dimensional model has been used in two-dimension for decreasing the computational cost. Firstly, it has been ensured that th...

متن کامل

Prediction of Bubble Point Pressure & Asphaltene Onset Pressure During CO2 Injection Using ANN & ANFIS Models

Although CO2 injection is one of the most common methods in enhanced oil recovery, it could alter fluid properties of oil and cause some problems such as asphaltene precipitation. The maximum amount of asphaltene precipitation occurs near the fluid pressure and concentration saturation. According to the description of asphaltene deposition onset, the bubble point pressure has a very special imp...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of the American Chemical Society

دوره 131 17  شماره 

صفحات  -

تاریخ انتشار 2009