The influence of temperature and storage time at RT on nucleation of the β phase in a 6082 Al–Mg–Si alloy

نویسندگان

  • C. D. Marioara
  • H. W. Zandbergen
چکیده

The age hardening process of a 6082 Al–Mg–Si alloy by isothermal ageing at 100, 125 and 150 °C for 0 to 40 days has been investigated by both conventional and high-resolution transmission electron microscopy. Changes in sizes and densities of the pre-β and β phases during ageing can explain the evolution of hardness, in particular a plateau in the curve of the hardness versus ageing time. Fully coherent pre-β particles (GP-I zones) are formed from atomic clusters that were created upon annealing or at natural ageing. Room temperature (RT) storage reduces the number of pre-β particles by a factor of 5. Ageing at 125 and 150 °C causes the phase pre-β to transform to the phase β . An ageing temperature of 100 °C was found to be too low to initiate the transformation of pre-β to β .  2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

بررسی اثر اکستروژن در کانال زاویه دار همسان بر رفتار پیر کرنشی دینامیکی یک آلیاژ Al-Mg-Si-Cu

An Al-Mg-Si-Cu alloy was subjected to tensile testing, both under solutionized and ECAE-ed conditions, using strain rates of 10-4 s-1 to 10-1 s-1 at temperatures of 25 ˚C to 325 ˚C to investigate the dynamic strain aging (DSA) phenomenon in the alloy. Negative strain rate sensitivity (m) and increasing ultimate tensile stress were observed in the DSA region with increasing temperature . Regardi...

متن کامل

Graphite Phase Formation in Al Alloyed Ductile Irons

The influence of aluminum, within the range of 0.08 - 6.16 wt.%, on the microstructure and hardness of as-cast ductile cast iron has been studied. A number of irons of different composition have been made by green sand casting and gravity die casting of appropriate design to provide the experimental materials. It has been found that Al addition and higher cooling rates in permanent mould castin...

متن کامل

ﺑﺮﺭﺳﻲ ﺍﺛﺮ ﻋﻤﻠﻴﺎﺕ ﺣﺮﺍﺭﺗﻲ ﻣﺤﻠﻮﻝ ﺳﺎﺯﻱ ﺑﺮ ﺭﻳﺰﺳﺎﺧﺘﺎﺭ ﻭ ﺧﻮﺍﺹ ﺳﺎﻳﺸﻲ ﺁﻟﻴﺎﮊ ﺁﻟﻮﻣﻴﻨﻴﻢ ۳۳۲

The effect of T6 heat treatment on the microstructure and wear behavior of Al-332 piston alloy containing 1.2wt% iron was investigated. The results showed that the T6 heat treatment changed the morphology of acicular eutectic Si particles to a more spherical form. The heat treatment also reduced the average length and blunted the needle-like ?- phase intermetallics through dissolution and fragm...

متن کامل

Crystallization Kinetics Study in Al87Ni10La3 Amorphous Alloy

In this study, the crystallization behavior of melt-spun Al87Ni10La3 amorphous phase was investigated by using X-ray diffraction and non-isothermal differential thermal analysis techniques. The results demonstrated that the amorphous phase exhibited two-stage crystallization on heating, i.e., at first step the amorphous phase transforms into α-Al phase and at second step Al11La3 and Al3Ni inter...

متن کامل

THE EFFECT OF CRYOLITE NA3ALF6 AND SODIUM FLUORIDE NAF ON THE CORROSION AND WETTING BY MOLTEN AL-SI ALLOY OF ANDALUSITE BASED REFRACTORIES

In order to improve the corrosion resistance of aluminosilicate refractories by molten aluminum, alkaline fluoride NaF and cryolite Na3AlF6 powders were studied. Both physical and chemical properties are known to influence wetting and corrosion behavior. This paper devoted to determine the influence of alkaline fluoride and cryolite added to andalusite based castable on the reaction with a...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2003