Phonon density of states of nanocrystalline Fe prepared by high-energy ball milling

نویسندگان

  • B. Fultz
  • J. L. Robertson
  • L. J. Nagel
  • S. Spooner
چکیده

We performed inelastic neutron scattering measurements on nanophase Fe powders prepared by high-energy ball milling. Neutron energy loss spectra were measured for two states of the material: ~1! as milled, when the material had a characteristic nanocrystallite size of 12 nm; and ~2! annealed, when the material had a characteristic crystallite size of 28 nm. The longitudinal peak in the phonon density of states ~DOS! of the nanophase Fe was broadened, compared to that of the annealed material. We attribute this broadening to short phonon lifetimes in nanocrystals. The nanophase material also showed an enhanced density of states at low energies below 15 meV, which may indicate the presence of intercrystallite vibrations. These differences in phonon DOS should have only a small effect on the difference in vibrational entropy of nanocrystalline and larger-grained Fe. © 1996 American Institute of Physics. @S0021-8979~96!00611-1#

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Phonons in Nanocrystalline 57Fe

We measured the phonon density of states (DOS) of nanocrystalline Fe by resonant inelastic nuclear g-ray scattering. The nanophase material shows large distortions in its phonon DOS. We attribute the high energy distortion to lifetime broadening. A damped harmonic oscillator model for the phonons provides a low quality factor, Qu, averaging about 5, but the longitudinal modes may have been broa...

متن کامل

Structural Characterization and Ordering Transformation of Mechanically Alloyed Nanocrystalline Fe-28Al Powder

The synthesis of nanocrystalline Fe3Al powder by mechanical alloying as well as the structural ordering of the synthesized Fe3Al particles during the subsequent thermal analysis were investigated. Mechanical alloying was performed up to 100 hours using a planetary ball mill apparatus with rotational speed of 300 rpm under argon atmosphere at ambient temperature. The synthesized powders were cha...

متن کامل

Nano-Crystalline Mg(2-x)MnxNi Compounds Synthesized by Mechanical Alloying: Microstructure and Electrochemistry

Mechanical alloying of binary and ternary elemental powder mixtures with the nominal compositions of Mg2Ni and Mg(2-x)MnxNi (x= 0, 0.05, 0.10 and 0.15 at. %) were carried out in a planetary ball mill for various milling times of 5, 10, 15, 20, 30 and 60 h. X-ray diffraction and field emission scanning and transmission electron microscopy were used for the characterization of the milled products...

متن کامل

Structural Evolution of Al-20% (wt) Al2O3 System during Ball Milling Stages

Production of nanostructured aluminum matrix composite powder by high energy ball milling is investigated. Scanning electron microscopy analysis as well as the tap and green density measurements were used to optimize the milling time needed for the completion of the mechanical milling process. Also, we studied the particles morphology and size distribution change with milling time and its corre...

متن کامل

Synthesis and properties of nanocrystalline compounds prepared by high-energy milling

Carbides, borides and nitrides of high melting transition metals were synthesized by high energy ball milling of elemental powder mixtures. The obtained hard material phases show a nanocrystalline structure with a saturation value of the crystal sizes between 7-8 nm. The kinetics of the reaction were investigated, and the nanocrystalline powders were densified by HIP. Introduction The formation...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 1996