Effect of dentin conditioners on the microtensile bond strength of a conventional and a self-etching primer adhesive system.

نویسندگان

  • Paula Jacques
  • Josimeri Hebling
چکیده

OBJECTIVE To investigate the effect of different dentin treatments on the microtensile bond strength of a self-etching primer and a simplified, total-etch adhesive system. METHODS Flat dentin surfaces were created on extracted human third molars. The surfaces were treated with one of the following conditioners: self-etching primer for 20 s (Clearfil SE Primer), 37% phosphoric acid for 15 s or 0.5 M EDTA for 30 s. Conditioned surfaces were then bonded with either Clearfil SE Bond or Single Bond followed by resin composite (Z250) build-ups constructed incrementally. Application of SE Primer was included when Clearfil SE Bond was used, after phosphoric acid and EDTA conditioning. After 24 h storage in water at 37 degrees C, the teeth were longitudinally sectioned across the bonded interface to produce beams with 1.0 mm2 of adhesive area, tested with the microtensile method at a rate of 0.5 mm/min. Data were analyzed using two-way ANOVA and Tukey's test. RESULTS The highest bond strength mean was found for the combination SE Primer/Single Bond (58.5+/-20.8 MPa), followed by the EDTA/Clearfil SE Bond (47.8+/-15.1 MPa) and phosphoric acid/Single Bond (40.9+/-14.3 MPa). The remaining combinations showed statistically similar (p>0.05) tensile bond strength. SIGNIFICANCE The bond performance of the adhesives tested was dependent on the dentin conditioner. Pre-treatment with a mild etchant such as 0.5 M EDTA improved the bond strength of Clearfil SE Bond. Single Bond performed better when a self-etching primer was used as the dentin conditioner, probably by preventing the formation of a defective zone at the base of the hybrid layer. Overall results indicate that higher bond strengths can be achieved by conditioning dentin with milder etchants, suggesting that deeper demineralization may prevent proper resin infiltration, hence compromising the bond.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effect of Saliva Contamination and sequencing time of curing the Transbond™ Plus Self Etching Primer on the Shear Bond Strength of Orthodontic Brackets

Abstract Background and aim: Over the years, improvments have been done to simplify clinical bonding procedure. One of these material is Transbond™ Plus Self Etching. The aim of this study was to evaluate the effect of saliva contamination and reusing Transbond™ Plus Self Etching Primer (SEP) on shear bond strength of orthodontic brackets. Materials and Methods: Fifty premolars divided into fiv...

متن کامل

Microtensile bond strength of clearfil SE bond to caries-affected dentin and normal dentin

Microtensile bond strength of clearfil SE bond to caries-affected dentin and normal dentin Dr. A. Ghasemi* - Dr. M. Bargrizan** - Dr. M. Mahmoodi*** *- Assistant Professor of Operative Dentistry Dept. - Faculty of Dentistry – Shaheed Beheshti University of Medical Sciences. **- Assistant Professor of Pedodontics Dept. - Faculty of Dentistry – Shaheed Beheshti University of Medical Sciences. ***...

متن کامل

Effect of high-power LED light curing unit on bond strength of composite resin to dentin

Purpose: This study evaluated the effect of a high-power solid-state light emitting diode (LED) curing unit on the dentin bond strength of a composite resin with self-etching primer adhesives by means of microtensile bond test. Materials and Methods: The flat dentin surfaces of the extracted human molars were prepared. Each surface was treated with either two self-etching adhesive systems (Clea...

متن کامل

Sodium fluoride addition to a two-step etch-and-rinse adhesive system: effect on dentin microtensile bond strength and durability

Introduction: Studies have suggested that sodium fluoride (NaF) has an inhibitory effect on the activity of endogenous matrix metalloproteinase enzymes. This study assessed the effect of a fluoride-containing adhesive on microtensile bond strength (µTBS) over time. Material & Methods: In this experimental study, 36 extracted  third molars were used to evaluate the µTBS of...

متن کامل

Comparison of Shear Bond Strength of Composite Restorations to Intact Enamel of Primary Incisors When Using Different Conditioners and Adhesive Systems

Introdouction: Esthetic demands of patients have led to the introduction of tooth-colored restorations wherecomposite resins are bonded to the enamel using acid etch techniques. Total etch adhesion systems are still considered as the gold standard among bonding systems. However, clinicians have a tendency to use adhesive systems with simpler application procedures. The aim of the present stu...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Dental materials : official publication of the Academy of Dental Materials

دوره 21 2  شماره 

صفحات  -

تاریخ انتشار 2005