Wear of a Total Knee Replacement with Antioxidant UHMWPE and Gradually Varying Sagittal Curvature

نویسندگان

  • MR Dressler
  • S Swope
  • J Tikka
  • C Hardaker
  • M Heldreth
  • T Render
چکیده

+MR Dressler, S Swope, J Tikka, C Hardaker, M Heldreth, T Render +DePuy Orthopaedics Research, Warsaw, IN [email protected] INTRODUCTION An estimated 46 million Americans suffer from osteoarthritis [1]. As tissue engineered treatments and other options remain on the horizon, total knee arthroplasty (TKA) continues to be an efficacious solution for severe osteoarthritis and has been increasingly applied to younger more active patients [2]. Consequently, new TKA devices are emerging that address previous challenges to long term success such as momentary instability, backside wear of modular devices, and oxidation of UHMWPE. The objective of this study was to evaluate the in vitro wear of a knee system with a novel femoral condyle geometry based upon a gradually changing sagittal curvature, refined tibio-femoral articulation, a new tibial insert locking mechanism, and an anti-oxidant containing poly material

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Reduction of Total Knee Replacement Wear with Vitamin E doped highly cross linked UHMWPE

Introduction: Ultra high molecular weight polyethylene (UHMWPE) is a common bearing component in Total Knee Replacement (TKR) implants, and its susceptibility to wear continues to be the long-term limiting factor in the life of these implants. Novel material modifications have been introduced to reduce UHMWPE wear rates and thus improve the life of TKRs. Radiation and crosslinking of UHMWPE hav...

متن کامل

Investigation of Wear Behavior of Biopolymers for Total Knee Replacements Through Invitro Experimentation

The average life span of knee prosthesis used in Total Knee Replacement (TKR) is approximately 10 to 15 years. Literature indicates that the reasons for implant failures include wear, infection, instability, and stiffness. However, the majority of failures are due to wear and tear of the prosthesis. The most common biopolymer used in TKR  is Ultra High Molecular Weight Polyethylene (UHMWPE). Pr...

متن کامل

Reduction of Wear in Fixed Bearing Total Knee Replacement Using Crosslinked Uhmwpe

Introduction Reduction of ultra high molecular weight polyethylene (UHMWPE) surface wear in total knee replacement (TKR) bearings may delay the onset of osteolysis and subsequent loosening of components. Crosslinking has been shown to increase the wear resistance of UHMWPE bearings in multidirectional total hip replacement applications when articulating against smooth counterfaces [1]. The aim ...

متن کامل

Effects of Tibial Insert Slope on Polyethylene Wear and Stress

INTRODUCTION: Both posterior stabilized (PS) and cruciate retaining (CR) total knee replacement systems have demonstrated high rates of survivorship, high clinical knee scores and high patient satisfaction scores for decades. However, CR total knees sometimes exhibit more varied kinematics and a smaller range of motion than similar PS knees. Many factors can cause this, but one important factor...

متن کامل

The effect of insert conformity and material on total knee replacement wear

The mean average life is increasing; therefore, there is a need to increase the lifetime of the prostheses. To fulfil this requirement, new prosthetic designs and materials are being introduced. Two of the design parameters that may affect wear of total knee replacements, and hence the expected lifetime, are the insert conformity and material. Computational models have been used extensively for...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2011