An empirical approach to characterizing trunk muscle coactivation using simulation input modeling techniques.
نویسندگان
چکیده
Accurately describing trunk muscle coactivation is fundamental to quantifying the spine reaction forces that occur during lifting tasks and has been the focus of a great deal of research in the spine biomechanics literature. One limitation of previous approaches has been a lack of consideration given to the variability in these coactivation strategies. The research presented in this paper is an empirical approach to quantifying and modeling trunk muscle coactivation using simulation input modeling techniques. Electromyographic (EMG) data were collected from 28 human subjects as they performed controlled trunk extension exertions. These exertions included isokinetic (10 and 45 degrees /s) and constant acceleration (50 degrees /s/s) trunk extensions in symmetric and asymmetric (30 degrees ) postures at two levels of trunk extension moment (30 and 80Nm). The EMG data were collected from the right and left pairs of the erector spinae, latissimus dorsi, rectus abdominis, external obliques and internal obliques. Each subject performed nine repetitions of each combination of independent variables. The data collected during these trials were used to develop marginal distributions of trunk muscle activity as well as a 10x10 correlation matrix that described how the muscles cooperated to produce these extension torques. These elements were then combined to generate multivariate distributions describing the coactivation of the trunk musculature. An analysis of these distributions revealed that increases in extension moment, extension velocity and sagittal flexion angle created increases in both the mean and the variance of the distributions of the muscular response, while increases in the rate of trunk extension acceleration decreased both the mean and variance of the distributions of activity across all muscles considered. Increases in trunk asymmetry created a decrease in mean of the ipsi-lateral erector spinae and an increase in the mean of all other muscles considered, but there was little change in the variance of these distributions as a function of asymmetry.
منابع مشابه
Reliability analysis of repairable systems using system dynamics modeling and simulation
Repairable standby system’s study and analysis is an important topic in reliability. Analytical techniques become very complicated and unrealistic especially for modern complex systems. There have been attempts in the literature to evolve more realistic techniques using simulation approach for reliability analysis of systems. This paper proposes a hybrid approach called as Markov system ...
متن کاملExact Modeling and Simulation of Saturated Induction Motors with Broken Rotor Bars Fault using Winding Function Approach
Winding function method (WFM) provides a detailed and rather simple analytical modeling and simulation technique for analyzing performance of faulty squirrel-cage induction motors (SCIMs). Such analysis is mainly applicable for designing on-line fault diagnosis techniques. In this paper, WFM is extended to include variable degree of magnetic saturation by applying an appropriate air gap functio...
متن کاملDetermination of settlement trough width and optimization of soil behavior parameters based on the design of experiment method (DOE)
The expansion of the settlement trough is an important factor in the risk assessment of the tunneling induced settlement. The increase of settlement trough requires buildings to be included in the impact zone, which causes damages. This paper conducts estimation of the settlement trough width (STW) using empirical approaches, field measurement data and numerical solutions. The credibility of th...
متن کاملAn empirical study on statistical analysis and optimization of EDM process parameters for inconel 718 super alloy using D-optimal approach and genetic algorithm
Among the several non-conventional processes, electrical discharge machining (EDM) is the most widely and successfully applied for the machining of conductive parts. In this technique, the tool has no mechanical contact with the work piece and also the hardness of work piece has no effect on the machining pace. Hence, this technique could be employed to machine hard materials such as super allo...
متن کاملStudy on implementation of one-piece lean line design using simulation techniques: A practical approach
This paper discusses the simulation study carried out for proposing one-piece lean line layout with features of Lean Manufacturing. The lean initiatives that can be addressed are, introducing Kanban replenishment sys-tem, better work-in-process, changing the layout, visual management techniques, standardized work for the re-duction of cycle time, number of workers, number of setups. To improve ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
- Journal of biomechanics
دوره 33 12 شماره
صفحات -
تاریخ انتشار 2000