Reduction of Common-mode Radiation by Terminating Guard Trace with Resistors

نویسندگان

  • Tetsushi Watanabe
  • Tohlu Matsushima
  • Yoshitaka Toyota
  • Osami Wada
  • Ryuji Koga
چکیده

A microstrip structure with a narrow return plane generates large common-mode radiation. The guard trace attached near the signal line can reduce common-mode radiation. In general, the guard trace needs a lot of via connections to the return plane for keeping the guard trace grounded. The guard trace with long intervals of vias causes resonance and additional radiation. We propose a novel technique for maintaining low radiation by using only two vias at both ends of the guard trace and adding a termination resistor to the guard trace. It was found that the matched termination suppresses guard trace resonance most effectively through a circuit simulation and radiation measurement. PCB1 PCB2 FPC

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Evaluation of EMI Reduction Effect of Guard Traces Based on Imbalance Difference Model

Placing a guard trace next to a signal line is the conventional technique for reducing the common-mode radiation from a printed circuit board. In this paper, the suppression of common-mode radiation from printed circuit boards having guard traces is estimated and evaluated using the imbalance difference model, which was proposed by the authors. To reduce common-mode radiation further, a procedu...

متن کامل

Increase of Common-Mode Radiation due to Guard Trace Voltage and Determination of Effective Via-Location

A guard trace placed near a signal line reduces commonmode radiation from a printed circuit board. The reduction effect is evaluated by the imbalance difference model, which was proposed by the authors, when the guard trace has exactly the same potential as the return plane. However, depending on interval of ground connection of the guard trace, the radiation can increase when the guard trace r...

متن کامل

Suppression of Guard-Trace Resonance by Matched Termination for Reducing Common-Mode Radiation

We propose a novel technique of matching at both ends of the guard trace to suppress resonance. This approach is derived from the viewpoint that the guard trace acts as a transmission line. We examined that matched termination suppresses guard-trace resonance through simulating a circuit and measuring radiation. We found from these results that the proposed method enables guard-trace voltages t...

متن کامل

Common-mode Current Due to Trace and Slit in Ground Plane and Effect of Guard Band

The common-mode (CM) current due to a trace near the PCB edge and across a slit in the ground plane is treated experimentally and by FDTD modeling. The width of the slit was 2 mm and the length was varied. The effect of a guard band with a 5 mm width is also discussed. As the slit length becomes longer, |S21| related to the CM current significantly increases. When the slit penetrates to the cen...

متن کامل

Suppression of Crosstalk Using Serpentine Guard Trace Vias

The reliability of circuits on printed circuit boards (PCBs) in many modern electronic products is affected by severe noise caused by high-speed and low-voltage operation as well as layout constraints compounded by limited space and high circuit density. Crosstalk is a major noise source that interferes with the signal integrity (SI) in poor PCB layout designs. One common method of reducing cro...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2009