Perovskite Solar Cells Fabricated by Using an Environmental Friendly Aprotic Polar Additive of 1,3-Dimethyl-2-imidazolidinone
نویسندگان
چکیده
Perovskite solar cells (PSCs) have great potentials in photovoltaics due to their high power conversion efficiency and low processing cost. PSCs are usually fabricated from PbI2/dimethylformamide solution with some toxic additives, such as N-methyl pyrrolidone and hexamethylphosphoramide. Here, we use an environmental friendly aprotic polar solvent, 1,3-dimethyl-2-imidazolidinone (DMI), to fabricate perovskite films. By adding 10 vol% DMI in the precursor solution, high-quality perovskite films with smooth surface are obtained. By increasing annealing temperature from 100 to 130 °C, the average grain size of the perovskite increases from ~ 216 to 375 nm. As a result, the efficiency of the PSCs increases from 10.72 to 14.54%.
منابع مشابه
Conversion of Sawdust into 5-Hydroxymethylfurfura by Using 1,3-Dimethyl-2-Imidazolidinone as the Solvent
The conversion of the cellulose into 5-HMF would experience three steps, cellulose to glycose, glycose to fructose and fructose to 5-HMF. Chloride ion can break down the hydrogen bond in cellucose, chromium can catalyze the isomerization of glycose to fructose, and the high temperature is helpful to cyclohydration of fructose to 5-HMF. In this paper, the sawdust has been directly degraded i...
متن کاملSelective dissolution of halide perovskites as a step towards recycling solar cells
Most research on perovskite solar cells has focused on improving power-conversion efficiency and stability. However, if one could refurbish perovskite solar cells, their stability might not be a critical issue. From the perspective of cost effectiveness, if failed, perovskite solar cells could be collected and recycled; reuse of their gold electrodes and transparent conducting glasses could red...
متن کاملبررسی اثر فازی آلومینا بر بلورینگی لایه پروسکایت در سلولهای خورشید پروسکایتی
Organic-inorganic perovskite (CH3NH3PbI3), due to an appropriate energy gap to absorb sunlight, is used as an absorbent layer in third generation solar cells. Crystallinity of light absorbing layer plays an important role in the performance of perovskite solar cells and substrate plays an important role on crystallinity of light absorbing layer. In superstructure solar cells, alumina (aluminum ...
متن کاملEfficient perovskite solar cells fabricated using an aqueous lead nitrate precursor.
A novel, aqueous precursor system (Pb(NO3)2 + water) is developed to replace conventional (PbI2 + DMF) for fabricating methylammonium lead iodide (MAPbI3) perovskite solar cells (PSCs). When the morphology and surface coverage of the Pb(NO3)2 film was controlled during coating, a power conversion efficiency of 12.58% under standard conditions (AM1.5, 100 mW cm(-2)) was achieved for the PSC.
متن کاملافزایش پایداری سلولهای خورشیدی با استفاده از لایههای جاذب پروسکایتی CH3NH3PbI3 آلاییده با برم
The CH3NH3PbI3 is one of the most widely used and famous lead halide perovskite absorber layer for using in perovskite solar cells. One of the ways to deal with the instability problem of this perovskite structure in environmental condition is bromide doping in this composition. In this work, the structural and optical properties of the bromide doped CH3NH3PbI3 absorber layers were studied as w...
متن کامل