Sensitivities of NO x transformation and the effects on surface ozone and nitrate
نویسنده
چکیده
As precursors to tropospheric ozone and nitrate, nitrogen oxide (NOx) in the present atmosphere and its transformation in response to emission and climate perturbations are studied by using the CAM-Chem model and air quality measurements from the National Emissions Inventory (NEI), Clean Air Status and Trends Network (CASTNET), and Environmental Protection Agency Air Quality System (EPA AQS). It is found that NOx transformations in present atmospheric conditions show different sensitivities over industrial and non-industrial regions. As a result, the surface ozone and nitrate formations can be divided into several regimes associated with the dominant emission types and relative levels of NOx and volatile organic compounds (VOC). Ozone production in industrial regions (the main NOx emission source areas) increases in warmer conditions and slightly decreases following an increase in NOx emissions due to NOx titration, which is opposite to the response in non-industrial regions. The ozone decrease following a temperature increase in non-industrial regions indicates that ozone production in regions that lack NOx emission sources may be sensitive to NOx transformation in remote source regions. The increase in NO2 from NOx titration over industrial regions results in an increase rate of total nitrate that remains higher than the increase rate of NOx emissions. The presented findings indicate that a change in the ozone concentration is more directly affected by changes in climate and precursor emissions, while a change in the nitrate concentration is affected by local ozone production types and their seasonal transfer. The sensitivity to temperature perturbations shows that a warmer climate accelerates the decomposition of odd nitrogen (NOy) during the night. As a result, the transformation rate of NOx to nitrate decreases. Examinations of the historical emissions and air quality records of a typical NOxlimited area, such as Atlanta and a VOC-limited area, such as Los Angeles further confirm the conclusions drawn from the modeling experiments.
منابع مشابه
Effect of Fiber Surface Treatment on Wear Characteristics of Carbon Fiber Reinforced Polyamide 6 Composites
Ozone modification method and air-oxidation were used for the surface treatment of polyacrylonitrile(PAN)-based carbon fiber. The surface characteristics of carbon fibers were characterized by X-ray photoelectron spectroscopy (XPS). The interfacial properties of carbon fiber reinforced polyamide 6 (CF/PA6) composites were investigated by means of the single fiber pull-out tests. As a result...
متن کاملHistopathological Investigation of the Effect of Ozonated Water on Skin Ulcer Healing Process in Isolation Stress Mouse Model
Background and Objective: Skin ulcers and their slow healing are considered as one of the important medical aspects. Nowadays, various antibiotics and materials are used to accelerate the wound healing process. One of the methods taken in the field of wound healing is using ozone. On the other hand, one of the factors that hurt the speed of wound healing is stress. Therefore, the present study ...
متن کاملAntibacterial and Immunomodulatory Effects of Hexamethylenetetramine (Methenamine) Silver Nitrate
Introduction: Currently, developing new antibacterial drugs as alternative antibiotics is a very active area of research, due to widspreading widespread prevalence of resistant strains of microorganisms. This work intends to investigate of antibacterial properties and influence on immune blood cells of the silver-based compound hexamethylenetetramine (methenamine) silver nitrate with general fo...
متن کاملNano-Structure Roughening on Poly(Lactic Acid)PLA Substrates: Scanning Electron Microscopy (SEM) Surface Morphology Characterization
Scanningelectron microscopy (SEM) has been utilized to examine the morphology and topography alterations in the surface of Poly(Lactic Acid)(PLA) fabrics due to UV/Ozoneirradiation. In the past decade, a growing attention in the usage of “Green Techniques” in industrial applications has been observed owing to many benefits such as low impurities and their relatively low cost to substitute th...
متن کاملAnticorrosive Performance of Polyester–melamine Coating Fortified with Zinc Ferrite Nanoparticles
In this study, nanoparticle zinc ferrites with different particle sizes were synthesized via sol-gel method using ferric nitrate and zinc nitrate. The obtained gel was dried and calcined at three different temperatures (i.e. 500, 600 and 800 °C) for 2 h. Adequate amounts of the as-synthesized nanoparticle samples were then added to the mixture of polyester resin and formaldehyde resin. The ...
متن کامل