Cold End Forming Of Welded Steel Tubes
نویسندگان
چکیده
The production of custom and specific tube end shapes by cold end forming using a die is generally limited to seamless tubular parts. Current research work in the field follows the same trend as that of industry and, therefore, there is no accumulated experience, no practical design rules, and no information available in the specialized literature concerning the utilization of tube end forming for shaping the end of thin-walled welded tubes. This paper is concerned with the lack of knowledge and is a contribution towards the understanding of the mechanics of deformation of tube end forming applied to welded tubes. The presentation addresses the influence of major operating parameters on the formability limits of the process with the purpose of understanding feasibility and establishing design rules for the benefit of those who design tubular parts in daily practice. The authors effectively contribute to transferable technological knowledge opening new market opportunities that stimulate innovations among carbon and stainless steel tubular products. DOI: 10.4018/978-1-4666-1867-1.ch013
منابع مشابه
Investigation on Formability of Tailor-Welded Blanks in Incremental Forming
Steel laser tailor-welded blanks (TWBs) are produced by end-to-end joining of base sheets using different welding methods. In this article, the formability of laser TWBs of St12 and St14 with thicknesses of 1 mm and 1.5 in single point incremental forming process were experimentally and numerically investigated. First, the forming limit wall angle was experimentally determined for each of the b...
متن کاملWelding Journal - October 2012
There are a wide range of important applications for metal tube materials in various fields. The production process of high-frequency longitudinally welded pipe includes first using a roller to coil the long steel strips of a certain size into a cylinder shape, and then join them by heating the steel materials at the welding edge with a high-frequency welding machine — Fig. 1. The processes inc...
متن کاملEffect of Prior Cold Work on the Mechanical Properties of Weldments
Heat exchanger units used in steam raising power plant are often manufactured using many metres of austenitic stainless steel tubes that have been plastically formed (bent and swaged) and welded into complex shapes. The amount of plastic deformation (pre-straining) before welding varies greatly. This has a significant effect on the mechanical properties of the welded tubes and on the final resi...
متن کاملUltimate Load Capacity and Behavior of Thin-Walled Curved-Steel Square Struts, Subjected to Compressive Load
There have been some experimental tests on hollow curved-steel struts with thin-walled square sections, in order to investigate their general behavior, particularly their capacity for bearing differing loads. One set of square tubes are cold-formed into segments of circular arcs with curvature radii, equal to 4000 mm. Different lengths of curved struts are fabricated so as to cover a practical ...
متن کاملFormability Study of Steel Tailor laser Welded Blanks (TWB) in Stretch Forming
The use of TWB has been developed in automotive industries because of it’s advantages such as reduction in weight, cost and fuel economy of vehicles. The main objective of the peresent work is to study the effects of weld zone, diffrence in surface coating and thickness ratio on the formability of TWB composed of AISI 304, SPCC and IF steel sheets. It was found that the narrow weld zone has lit...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- IJMMME
دوره 1 شماره
صفحات -
تاریخ انتشار 2011