A chip off the old block!

نویسندگان

  • R Allott
  • A R Naylor
چکیده

A 35 year old male presented 9 months after sustaining a penetrating injury to the neck with a false aneurysm of the common carotid artery (CCA). At exploration, a 5mm piece of granite was embedded in the posterior wall of the CCA with overlying endothelialisation. He was treated with segmental resection and an interposition vein graft. Apart from the risk of foreign body embolisation at the time of the original presentation, it seems remarkable that the patient did not suffer a stroke due to embolism of thrombus that one would normally have expected to form on the highly thrombogenic stone surface.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Optimization of Material Removal Rate in Electrical Discharge Machining Alloy on DIN1.2080 with the Neural Network and Genetic Algorithm

Electrical discharge machining process is one of the most Applicable methods in Non-traditional machining for Machining chip in Conduct electricity Piece that reaching to the Pieces that have good quality and high rate of machining chip is very important. Due to the rapid and widespread use of alloy DIN1.2080 in different industry such as Molding, lathe tools, reamer, broaching, cutting guillot...

متن کامل

New Method for Analysis of image sensor to produce and evaluate the image

In this paper, a new method for evaluating CMOS image sensors based on computer modeling and analysis is introduced. Image sensors are composed of different parts, each of which has a specific effect on image quality. Circuits of image sensors can be evaluated and analyzed using circuit simulators or theoretically, but these methods cannot help to produce the final image. In order to produce th...

متن کامل

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

متن کامل

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

متن کامل

Off-Chip Memory Traffic Measurements of Low-Power Embedded Systems

In all processors, power can be saved by making effective use of on-chip memory. For embedded systems this is crucial, since they often drain their power from a pair of batteries. In this paper, we experimentally measure the amount of off-chip traffic produced by several caches. It is shown that large savings can be achieved if size, associativity, and block size are well-chosen. Most examined ...

متن کامل

Scratchpad memories vs locked caches in hard real-time systems: a qualitative and quantitative comparison

Hard real-time tasks must meet their deadline in all situations, including in the worst-case one, otherwise the safety of the controlled system is jeopardized. In addition to this stringent demand for predictability, an increasing number of hard real-time applications need to be fast as well. As a consequence, architectures with caches and/or on-chip static RAM (scratchpad memories) are of inte...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • European journal of vascular and endovascular surgery : the official journal of the European Society for Vascular Surgery

دوره 33 6  شماره 

صفحات  -

تاریخ انتشار 2007