Marginal quality of flowable 4-mm base vs. conventionally layered resin composite.
نویسندگان
چکیده
OBJECTIVE This study evaluated marginal integrity of bonded posterior resin composite fillings to enamel and dentine with and without 4mm flowable base, before and after thermo-mechanical loading (TML). METHODS 80 MOD cavities with one proximal box beneath the CEJ were prepared in extracted human third molars. Direct resin composite restorations (SDR with CeramX mono, Tetric EvoCeram, Filtek Supreme XT, and Venus Diamond or the respective resin composites alone) were bonded with system immanent adhesives XP Bond, Xeno V, Syntac, Adper Prompt L-Pop, and iBond self-etch. Before and after thermomechanical loading (100,000×50N, 2500 thermocycles between 5 and 55°C), marginal gaps were analysed using SEM of epoxy resin replicas. Results were analysed with Kruskal-Wallis and Mann-Whitney U-tests (p<0.05). After thermomechanical loading, specimens were cut longitudinally in order to investigate internal dentine adaptation by epoxy replicas under a SEM (200× magnification). RESULTS In enamel, high percentages of gap-free margins were initially identified for all adhesives. After TML, etch-and-rinse adhesives performed better than self-etch adhesives (p<0.05). Also in dentine, initially high percentages of gap-free margins were found for all adhesives. After TML, etch-and-rinse adhesives again performed better than self-etch adhesives for both marginal and internal adaptation (p<0.05). The presence of a 4mm layer of SDR had no negative influence on results in any group (p>0.05). CONCLUSIONS SDR as 4mm bulk fill dentine replacement showed an good performance with the material combinations under investigation.
منابع مشابه
In Vitro Evaluation of Marginal Sealing Ability of Bulk Fill Flowable Composite Resins
Aim: The purpose of this study is to analyse marginal sealing ability of bulk fill flowable composite resins. Materials and Methods: A standard class V cavity (3 mm mesiodistal width, 3 mm occlusogingival height, and 1.5 mm axial depth) will be prepared at the cementoenamel junction (CEJ) on the facial surface of eighty human teeth with a 0.5 mm wide 45° beveled enamel margin and a 90° cervical...
متن کاملMicroleakage in class II restorations: open vs closed centripetal build-up technique.
PURPOSE This study evaluated whether a Class II restoration in a flowable resin composite has to be placed prior to (open-sandwich technique) or after (closed-sandwich technique) construction of the interproximal wall in the centripetal build-up technique in order to reduce microleakage. METHODS AND MATERIALS Thirty non-carious molars were selected and randomly divided into two groups (n = 15...
متن کاملComparing the Microleakage of Bulk-Fill (flowable, packable) Composite Restorations and Conventional Light-cured Composites
Introduction and aim: Bulk Fill composites have increased polymerization depth and their contraction stress, and cuspal deflection are reduced in comparison with conventional composites. Therefore, it is claimed that their microleakage is reduced. The aim of this study was to compare microleakage of (flowable and packable) Bulk Fill and conventional resin composites. Materials and Methods: Thi...
متن کاملInterfacial microscopic examination and chemical analysis of resin-dentin interface of self-adhering flowable resin
The newly introduced self-adhering flowable resin-composites Background: decrease the required time for application by incorporation of an acidic adhesive monomer, thus reducing the number of steps, but its bonding is still uncertain. The aim of this study was to evaluate the interfacial microscopic examination and chemical analysis at the resin-dentin interface of a self-adhering flowable resi...
متن کاملInterfacial microscopic examination and chemical analysis of resin-dentin interface of self-adhering flowable resin composite
Background: The newly introduced self-adhering flowable resin-composites decrease the required time for application by incorporation of an acidic adhesive monomer, thus reducing the number of steps, but its bonding is still uncertain. The aim of this study was to evaluate the interfacial microscopic examination and chemical analysis at the resin-dentin interface of a self-adhering flowable resi...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of dentistry
دوره 39 10 شماره
صفحات -
تاریخ انتشار 2011