Effects of Material Properties of Warhead Casing on Natural Fragmentation Performance of High Explosive (HE) Warhead

نویسندگان

  • G. Tanapornraweekit
  • W. Kulsirikasem
چکیده

This research paper presents numerical studies of the characteristics of warhead fragmentation in terms of initial velocities, spray angles of fragments and fragment mass distribution of high explosive (HE) warhead. The behavior of warhead fragmentation depends on shape and size of warhead, thickness of casing, type of explosive, number and position of detonator, and etc. This paper focuses on the effects of material properties of warhead casing, i.e. failure strain, initial yield and ultimate strength on the characteristics of warhead fragmentation. It was found that initial yield and ultimate strength of casing has minimal effects on the initial velocities and spray angles of fragments. Moreover, a brittle warhead casing with low failure strain tends to produce higher number of fragments with less average fragment mass. Keywords—Detonation, Material Properties, Natural Fragment, Warhead

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

FEM Simulation of HE Blast-Fragmentation Warhead and the Calculation of Lethal Range

This paper presents the simulation of fragmentation warhead using a hydrocode, Autodyn. The goal of this research is to determine the lethal range of such a warhead. This study investigates the lethal range of warheads with and without steel balls as preformed fragments. The results from the FE simulation, i.e. initial velocities and ejected spray angles of fragments, are further processed usin...

متن کامل

Simulation Study on Jet Formability and Damage Characteristics of a Low-Density Material Liner

The shaped charge tandem warhead is an effective weapon against the ERA (explosive reactive armor). Whether the pre-warhead can reliably initiate the ERA directly determines the entire performance of the tandem warhead. The existing shaped charge pre-warhead mostly adopts a metal shaped jet, which effectively initiates the ERA, but interferes the main shaped jet. This article, on the other hand...

متن کامل

Modeling and Analysis of Viscous Dissipation Phenomenon on Temperature Distribution in the Process of Injection Explosive Fluid

The explosive viscous liquid becomes inject to warhead by discharge system. The injection device is consisted of a piston to move down and leads the viscous fluid through the cylindrical pipe towards the end of the duct. Then the viscous fluid leads into a convergent path that will be injected to the warhead or other injection equipment. In this project, the path of viscous fluid flow is divide...

متن کامل

مقایسه عملکرد اکتول و PBXN-110 در یک سرجنگی خرج گود

The jet formation caused by the collapse of a liner is dependent mainly upon the explosive characteristics loaded in shaped charge warhead. In this study, the purpose was to compare the influence of Octol and PBXN-110 fillers on performance of a specific shaped charge warhead. This material loaded into the aluminum-cased shaped charge having a 35° copper  liner and 510 cm3 in capacity. Results ...

متن کامل

A New Approach to Nuclear Warhead Verification Using a Zero-Knowledge Protocol

Warhead verification systems proposed to date fundamentally rely on the use of information barriers to prevent the release of sensitive information. Measurements with information barriers significantly increase the complexity of inspection systems, make their certification and authentication difficult, and may reduce the overall confidence in the verifiability of future arms-control agreements....

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2011