A thermoelectric energy harvester with a cold start of 0.6 °C

نویسندگان

  • P. Mullen
  • J. Siviter
  • A. Montecucco
  • A. R. Knox
چکیده

This paper presents the electrical and thermal design of a thermoelectric energy harvester power system and its characterisation. The energy harvester is powered by a single Thermoelectric Generator (TEG) of 449 couples connected via a power conditioning circuit to an embedded processor. The aim of the work presented in this paper is to experimentally confirm the lowest ΔT measured across the TEG (ΔTTEG) at which the embedded processor operates to allow for wireless communication. The results show that when a temperature difference of 0.6°C ΔTTEG is applied across the thermoelectric module, an input voltage of 23 mV is generated which is sufficient to activate the energy harvester in approximately 3 minutes. An experimental setup able to accurately maintain and measure very low temperatures is described and the electrical power generated by the TEG at these temperatures is also described. It was found that the energy harvester power system can deliver up to 30 mA of current at 2.2 V in 3 ms pulses for over a second. This is sufficient for wireless broadcast, communication and powering of other sensor devices. The successful operation of the wireless harvester at such low temperature gradients offers many new application areas for the system, including those powered by environmental sources and body heat. © 2014 Elsevier Ltd. All rights reserved. Selection and peer-review under responsibility of Conference Committee members of the 12th European Conference on Thermoelectrics.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

A Research for the Thermoelectric Energy Harvester to Improve the Power Generation Efficiency

This study suggests using thermoelectric element to generate electric energy from the heat source efficiently. This generator system consists of a Heater, the Lower Heat Transfer Plate to absorb heat from the Heater, Two-Stage Thermoelectric Device module to generate the electric power with the heat transferred from the Lower Heat Transfer Plate, the Upper Heat Transfer Plate to convey the heat...

متن کامل

Manufacturing and Characterization of a Thermoelectric Energy Harvester Using the CMOS-MEMS Technology

The fabrication and characterization of a thermoelectric energy harvester using the complementary metal oxide semiconductor (CMOS)-microelectromechanical system (MEMS) technology were presented. The thermoelectric energy harvester is composed of eight circular energy harvesting cells, and each cell consists of 25 thermocouples in series. The thermocouples are made of p-type and n-type polysilic...

متن کامل

Power Management Electronics for Thermoelectric Energy Harvesting Systems

The presented paper gives an overview of basic principles and recent trends in power management electronics for thermoelectric energy harvesting. Energy harvesting systems are a modern way how to feed the autonomous devices on-site using ambient energy. The ambient energy in the case of thermoelectric generators is represented by temperature gradients. Different temperatures are applied to the ...

متن کامل

Effect of conjugate heat transfer in designing thermoelectric beverage cooler

Peltier technology opens new opportunities for special applications. In the current project, this technology was applied to design and fabricate a portable thermoelectric beverage cooler and thermoelectric cup. The simulation and results of the experiment showed that the common beverage cooler is not a suitable design for ignoring the effect of natural convection in cooling. In our thermoel...

متن کامل

A 10 mV-Input Boost Converter With Inductor Peak Current Control and Zero Detection for Thermoelectric and Solar Energy Harvesting With 220 mV Cold-Start and -14.5 dBm, 915 MHz RF Kick-Start

A boost converter for thermoelectric energy harvesting in 130 nm CMOS achieves energy harvesting from a 10 mV input, which allows wearable body sensors to continue operation with low thermal gradients. The design uses a peak inductor current control scheme and duty cycled, offset compensated comparators to maintain high efficiency across a broad range of input and output voltages. The measured ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015