The dental curing light: A potential health risk.
نویسندگان
چکیده
Powerful blue-light emitting dental curing lights are used in dental offices to photocure resins in the mouth. In addition, many dental personnel use magnification loupes. This study measured the effect of magnification loupes on the "blue light hazard" when the light from a dental curing light was reflected off a human tooth. Loupes with 3.5x magnification (Design for Vision, Carl Zeiss, and Quality Aspirator) and 2.5x magnification (Design for Vision and Quality Aspirator) were placed at the entrance of an integrating sphere connected to a spectrometer (USB 4000, Ocean Optics). A model with human teeth was placed 40 cm away and in line with this sphere. The light guide tip of a broad-spectrum Sapphire Plus (Den-Mat) curing light was positioned at a 45° angle from the facial surface of the central incisor. The spectral radiant power reflected from the teeth was recorded five times with the loupes over the entrance into the sphere. The maximum permissible cumulative exposure times in an 8-hr day were calculated using guidelines set by the ACGIH. It was concluded that at a 40 cm distance, the maximum permissible cumulative daily exposure time to light reflected from the tooth was approximately 11 min without loupes. The weighted blue irradiance values were significantly different for each brand of loupe (Fisher's PLSD p < 0.05) and were up to eight times greater at the pupil than when loupes were not used. However, since the linear dimensions of the resulting images would be 2.5 to 3.5x larger on the retina, the image area was increased by the square of the magnification and the effective blue light hazard was reduced compared to without the loupes. Thus, although using magnification loupes increased the irradiance received at the pupil, the maximum cumulative daily exposure time to reflected light was increased up to 28 min. Further studies are required to determine the ocular hazards of a focused stare when using magnification loupes and the effects of other curing lights used in the dental office.
منابع مشابه
A comparative study of the effects of QTH and LED light curing units on the surface hardness of colored compomer and Hybrid composites
Introduction: One factor affecting the degree of polymerization is the type of light-curing device. The aim of this study was to compare the effects of LED and QTH light curing units on the surface hardness of composite and compomer. Materials & Methods: In this experimental study, 30 samples of composite and compomer were divided into 3 groups of 10 each. One-half of the subgroups in each g...
متن کاملبررسی کارائی دستگاههای لایتکیور در مطبهای دندانپزشکی خصوصی شهر تهران در سال 1384
Background and Aim: Light cured composites and other restorative materials are quite common in dentistry today. Successful restorations are dependent on efficiency of curing light unit, eg. the intensity of emitted light and its wave length. The aim of this study was to evaluate the efficiency units of curing, in private dental offices in Tehran. Materials and Methods: In this descriptive cross...
متن کاملColor Stability of a Microhybrid Resin Composite Polymerized with LED and QTH Light Curing Units
Introduction: Discoloration of resin composites is a common reason for replacement of these restorations. The aim of this study was to eva-luate the influence of different light curing de-vices on color stability of a microhybrid resin composite. Materials and Methods: 80 disc-shaped speci-mens (8 mm in diameter, 2-mm height) were fabricated from filtek Z250 resin composite. Specimens wer...
متن کاملThe Effect of Standard and Extended Curing Time in Different Distances on Composite’s Degree of Conversion
Introduction: The aim of this study was to in-vestigate the effect of irradiation duration and distance of light tip to prepared samples in two different light curing unites on the degree of conversion of resin composite. Materials and Methods: Conventional halogen and blue Light emitting diode (LED) units were used for polymerization of an Opalis resin com-posite. The conversion measurements w...
متن کاملHardness of composite resin polymerized with different light-curing units
Introduction: The degree of polymerization depends on the type of light-curing unit. The aim of this study was to compare the hardness of composite resin cured by LED and Halogen light curing units. Methods: In this experimental study, 20 cylindrical samples of Tetric Ceram composite were prepared. Half of them were cured with Ultralume 2 LED and the other half with Astralis 7 Halogen light ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of occupational and environmental hygiene
دوره 13 8 شماره
صفحات -
تاریخ انتشار 2016