Odontologic use of copper/aluminum alloys: mitochondrial respiration as sensitive parameter of biocompatibility.

نویسندگان

  • Luiz Erlon A Rodrigues
  • Antônio A V F Carvalho
  • Antônio L M Azevedo
  • Cecília B B V Cruz
  • Antônio Wanderley C Maia
چکیده

Copper/aluminum alloys are largely utilized in odontological restorations because they are less expensive than gold or platinum. However, tarnishing and important corrosion in intrabuccal prostheses made with copper/aluminum alloys after 28 days of use have been reported. Several kinds of food and beverage may attack and corrode these alloys. Copper is an essential component of several important enzymes directly involved in mitochondrial respiratory metabolism. Aluminum, in contrast, is very toxic and, when absorbed, plasma values as small as 1.65 to 21.55 microg/dl can cause severe lesions to the nervous system, kidneys, and bone marrow. Because mitochondria are extremely sensitive to minimal variation of cellular physiology, the direct relationship between the mitocondrial respiratory chain and cell lesions has been used as a sensitive parameter to evaluate cellular aggression by external agents. This work consisted in the polarographic study of mitochondrial respiratory metabolism of livers and kidneys of rabbits with femoral implants of titanium or copper/aluminum alloy screws. The experimental results obtained did not show physiological modifications of hepatic or renal mitochondria isolated from animals of the three experimental groups, which indicate good biocompatibility of copper/ aluminum alloys and suggest their odontological use.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effect of Temperature on Diffusion-Bonded Joint of AZ31 Magnesium and 7075 Aluminum Alloy

In this study, the effect of temperature on the diffusion welding of AZ31 magnesium alloy and 7075 aluminum was discussed. Diffusion welding temperature was the most important parameter since all mechanisms are sensitive to temperature in Diffusion welding method. Intrusive contacts between the two alloys at temperatures of 430, and 440 °C 450 and took 60 min. In all tests constant pressure and...

متن کامل

Effect of Temperature on Diffusion-Bonded Joint of AZ31 Magnesium and 7075 Aluminum Alloy

In this study, the effect of temperature on the diffusion welding of AZ31 magnesium alloy and 7075 aluminum was discussed. Diffusion welding temperature was the most important parameter since all mechanisms are sensitive to temperature in Diffusion welding method. Intrusive contacts between the two alloys at temperatures of 430, and 440 °C 450 and took 60 min. In all tests constant pressure and...

متن کامل

Control Of C/Ti Ratio in Titanium Carbide - Copper Master Alloys Produced by SHS Reactions and its Effect on the Carbide Dispersion In Liquid Copper

Titanium carbide is used as an attractive reinforcement to produce particulate metal matrix composites. One of the problems to use this carbide as a reinforcement in copper-based composites is the lack of wetability in Cu-TiC system. This property improves as the C/Ti ratio in carbide decreases. Problems to use this carbide as a reinforcement in copper-based composites is the lack of wetabiity...

متن کامل

Control Of C/Ti Ratio in Titanium Carbide - Copper Master Alloys Produced by SHS Reactions and its Effect on the Carbide Dispersion In Liquid Copper

Titanium carbide is used as an attractive reinforcement to produce particulate metal matrix composites. One of the problems to use this carbide as a reinforcement in copper-based composites is the lack of wetability in Cu-TiC system. This property improves as the C/Ti ratio in carbide decreases.&#10Problems to use this carbide as a reinforcement in copper-based composites is the lack of wetabii...

متن کامل

The Parameters Investigation and Hardness Optimization of A380 Aluminum Alloy produced by Mechanical Vibrator

The use of aluminum alloys in various industries, especially the automotive industries, to have less structural weight, is on the rise. The use of semi-solid forming process in addition to changes in the microstructure which improves the mechanical properties can reduce the volume of production and ultimately lead to the improvement of the structural weight. In this paper, optimization of the g...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:
  • Brazilian dental journal

دوره 14 1  شماره 

صفحات  -

تاریخ انتشار 2003