Effect of microstructure on the fatigue of hot-rolled and cold-drawn NiTi shape memory alloys
نویسندگان
چکیده
We present results from a systematic study linking material microstructure to monotonic and fatigue properties of NiTi shape memory alloys. We consider Ni-rich materials that are either (1) hot rolled or (2) hot rolled and cold drawn. In addition to the two material processing routes, heat treatments are used to systematically alter material microstructure giving rise to a broad range of thermal, monotonic and cyclic properties. The strength and hardness of the austenite and martensite phases initially increase with mild heat treatment (300 ◦C), and subsequently decrease with increased aging temperature above 300 ◦C. This trend is consistent with transmission electron microscopy observed precipitation hardening in the hot-rolled material and precipitation hardening plus recovery and recrystallization in the cold-drawn materials. The low-cycle pseudoelastic fatigue properties of the NiTi materials generally improve with increasing material strength, although comparison across the two product forms demonstrates that higher measured flow strength does not assure superior resistance to pseudoelastic cyclic degradation. Fatigue crack growth rates in the hot-rolled material are relatively independent of heat treatment and demonstrate similar fatigue crack growth rates to other NiTi product forms; however, the cold-drawn material demonstrates fatigue threshold values some 5 times smaller than the hot-rolled material. The difference in the fatigue performance of hot-rolled and cold-drawn NiTi bars is attributed to significant residual stresses in the cold-drawn material, which amplify fatigue susceptibility despite superior measured monotonic properties. © 2007 Elsevier B.V. All rights reserved.
منابع مشابه
TRANSFORMATION BEHAVIOR OF NiTi SHAPE MEMORY ALLOYS TREATED BY THERMOMECHANICAL PROCESSING USING DSC
Abstract: In the present study the effect of thermomechanical treatment (cold work and annealing) on the transformation behavior of NiTi shape memory alloys was studied. Differential scanning calorimetry was used to determine transformation temperature and its relation to precipitates and defects. Three alloys including Ti-50.3at.% Ni, Ti-50.5at.% Ni (reclamated orthodontic wires) and 50.6at...
متن کاملDissimilar laser welding of NiTi shape memory alloy to austenitic stainless steel archwires
In this research, dissimilar welding of NiTi shape memory alloy to AISI 304 austenitic stainless steel Archwires was investigated. For this purpose, common straight orthodontic archwire with rectangular cross-section and dimensions of (0.635 × 0.432 mm) were selected and the laser welding technique was used to connect the wires. The microstructure, chemical composition and phasesin the weld zon...
متن کاملDissimilar laser welding of NiTi shape memory alloy to austenitic stainless steel archwires
In this research, dissimilar welding of NiTi shape memory alloy to AISI 304 austenitic stainless steel Archwires was investigated. For this purpose, common straight orthodontic archwire with rectangular cross-section and dimensions of (0.635 × 0.432 mm) were selected and the laser welding technique was used to connect the wires. The microstructure, chemical composition and phasesin the weld zon...
متن کاملEffect of the Primary Microstructures during Training Producers on TWSME in NiTi Alloys (TECHNICAL NOTE)
The influence of the martensitic, martensitic+austenitic and austenitic structures in bending training on two-way shape memory effect (TWSME) in Ni-50.8 at %Ti and Ni-49.9 at %Ti alloys was studied. In addition of the primary structure, the effect of pre-strain, plastic strain, training cycle and training temperature on the TWSME was investigated. The prepared samples were trained in martensiti...
متن کاملEffect of Electrical Current on Nitinol Medical Staples Shape Memory
Medical staples are one of the nitinol shape memory alloys applications which their pedicles have to be bent for suitable function with an appropriate angle at a specified temperature .It is achievable by shape memory effect. For this purpose, samples of nitinol super elastic alloys were bent in a steel mold with different angles & formed orthopedic staples. Then shape memory effect was induced...
متن کامل