Fabrication and Material Characterization of Silver Cantilevers via Direct Surface Micromachining

نویسنده

  • Eric W. Lam
چکیده

Microelectromechanical Systems (MEMS) rely heavily on the semiconductor industry’s manufacturing paradigm. While the standardized process model allows semiconductor chips to benefit from economy of scale and be sold at low prices, MEMS devices use specialized processes and subsequently have to be sold at higher prices. This severely hinders MEMS development because it is not economically feasible to research and develop specialized devices where only small volumes are needed. As such, tools and processes which divorce MEMS fabrication from this paradigm are needed. Using Hewlett-Packard thermal inkjet technology mounted to an X-Y microcontroller stage, we present a mask-less, or direct, surface micromachining process flow with a 250°C thermal budget. The process uses Cabot Corp.’s silver-based conductive ink for the structural layer and PMMA for the sacrificial layer. Several other materials were tested for use as sacrificial inks in addition to PMMA. Silver cantilevers with dimensions of 200x50μm and 200x100μm were fabricated as a demonstration of the process. The silver cantilevers were mechanically characterized by using force-deflection measurements made by a P-10 contact profilometer or a Hysitron nanoindentor. We present findings of 21.9±1.50GPa or 22±1.5GPa for the silver ink’s Young's modulus of elasticity, depending on the characterization method. These measurements were consistent with results measured by nanoindentating Cabot silver films. We hypothesize that the film’s porosity is the cause of the silver’s reduced material properties. Some preliminary data supporting this hypothesis is provided, and potential methods of improving the material properties and the surface micromachining process are discussed. Thesis Supervisor: Martin A. Schmidt Title: Professor of Electrical Engineering & Computer Science

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

On the fabrication and characterization of Al5083/Al2O3 surface nanocomposite via friction stir processing

In the present study, Al5083- Al2O3 nanocomposite was successfully prepared by friction stir processing (FSP) with rotational speed of 710 rpm and travel speed of 14 mm/min. In order to improve distribution of Al2O3 particles, a net of holes were designed on the surface of Al5083 sheet. The samples were characterized by optical and scanning electron microscopy (SEM), microhardness, tensile and ...

متن کامل

Tuning a racetrack ring resonator by an integrated dielectric MEMS cantilever.

The principle, fabrication and characterization of a dielectric MEMS cantilever located a few 100 nm above a racetrack ring resonator are presented. After fabrication of the resonators on silicon-on-insulator (SOI) wafers in a foundry process, the cantilevers were integrated by surface micromachining techniques. Off-state deflections of the cantilevers have been optimized to appropriately posit...

متن کامل

Step-Height Measurement of Surface Functionalized Micromachined Microcantilever Using Scanning White Light Interferometry.

Micro-cantilever arrays with different dimensions are fabricated by micromachining technique onto silicon <1 0 0> substrate. These sputtered Gold-Coated micro-cantilevers were later surface functionalized. Scanning Electron Microscopy, Atomic Force Microscopy and Optical SWLI using LASER probe are employed to characterize the morphology and image measurement of the micro-cantilever arrays, resp...

متن کامل

Synthesis and Characterization of Silver/Alumina Powders

In this research, synthesis and characterization of silver/alumina composite powders was investigated. This kind of metal/ceramic composite powders is used for fabrication of cutting tools inserts. The role of silver is toughening the final product. The powders were synthesized via co-precipitation method. The composition of the synthesized powders was Ag/80% wt 〖Al〗_2 O_3. Silver nitrate, alum...

متن کامل

Fabrication and Characterization of the Fiber Optical Taper for a Surface Plasmon Resonance Sensor

For a fiber optical surface plasmon resonance (SPR) sensor a short part of its cladding should be removed to coat a thin layer of a metal. Usually this is problematic when an optical fiber with small core diameter is used. In this paper, a new method using &micro;liter droplet of the HF acid for short fiber optical taper fabrication is reported. Using this method in a multi-mode optical fiber w...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2008