Effects of cold preservation on the lung mechanical properties in rats.

نویسندگان

  • K Ikeyama
  • H Sakai
  • M Omasa
  • T Nakamura
  • H Hamakawa
  • T Fujinaga
  • T Fukuse
  • H Wada
چکیده

In lung transplantation, cold preservation is an important process. However, the mechanical changes in the airway and tissue during cold preservation, especially before reperfusion, are unknown. To test the hypothesis that the mechanical changes in the airway and lung parenchyma start during cold preservation, we investigated the mechanical properties of the rat lung as a whole organ and in excised lung strips. In the 0 h group, the lungs were not preserved. In the 9 and 24 h group, the lungs were preserved for 9 and 24 h at 4 degrees C. After preservation, we evaluated the static compliance (Csta) of the whole lung as obtained from the pressure volume curves (n=5 in each group). Also, we measured the input impedance taken by a computer-controlled small-animal ventilator (n=9 in each group). All data were analyzed using a homogeneous linear model, which includes airway resistance (Raw), tissue elastance (H), and tissue resistance (G). Hysteresivity (eta) was calculated as G/H. Moreover, the tissue elasticity (Eqs) obtained from the quasi-static stress-strain curves was compared. There was no significant difference in Csta among the three groups. Raw was significantly lower in the 24 h group than in the 0 h group (p<0.01). Eqs was significantly higher in the preserved groups than in the 0 h group (p<0.01). These results demonstrated that the changes in the three mechanical properties of the airway and the tissue started within 9 h of preservation.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Evaluation of the Mechanical Properties of the cement treated Cold-in-Place Recycled Asphalt Mixtures

Cold-in-place recycling (CIR) is an environmentally sustainable alternative for preservation of asphalt pavements. A major disadvantage of this practice is the lower strength of the cold-in-place mixtures. Addition of cement into this type of mixture is a method for increasing its bearing capacity. The effect of cement content on the mechanical properties of the cold-in-place recycled asphalt m...

متن کامل

Investigating the Effects of Cold Bulge Forming Speed on Thickness Variation and Mechanical Properties of Aluminum Alloys: Experimental and Numerical

In this work, cold bulge forming of an Aluminium-Magnesium (Al-Mg) sheet with a solid bulging medium is performed experimentally and numerically.  Mechanical properties and thickness variations of Al-Mg sheet are evaluated before and after the forming process.  The results indicated that the Al-Mg sheet has taken the desired shape without necking using the cold bulge forming process.  Also, the...

متن کامل

The effects of vitamin B12 and diclofenac and their combination on cold and mechanical allodynia in a neuropathic pain model in rats

The present study was performed to investigate the effects of long-term intraperitoneal (IP) injection of vitamin B12 and diclofenac in separate and combined treatments on cold and mechanical allodynia in a neuropathic pain model in rats. Neuropathic pain was induced by crush injury in right tibial nerve. Acetone spray and von Frey tests were used to obtain cold and mechanical allody...

متن کامل

Investigation of the mechanical properties of cold roll welded Brass and IF steelproduced by cold roll bonding process

Cold roll bonding (CRB) is a solid state welding process, where the bonding is established by compressive plastic deformation of the metals. This process is applicable for a large number of materials. In addition, materials that cannot be bonded by traditional fusion-based processesmight be bonded by CRB process. In this research, cold roll welding of brass and IF steel was studied .The effects...

متن کامل

Investigation of the mechanical properties of cold roll welded Brass and IF steelproduced by cold roll bonding process

Cold roll bonding (CRB) is a solid state welding process, where the bonding is established by compressive plastic deformation of the metals. This process is applicable for a large number of materials. In addition, materials that cannot be bonded by traditional fusion-based processesmight be bonded by CRB process. In this research, cold roll welding of brass and IF steel was studied .The effects...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • European surgical research. Europaische chirurgische Forschung. Recherches chirurgicales europeennes

دوره 37 2  شماره 

صفحات  -

تاریخ انتشار 2005