In Vitro Solubility and Wear Rates of Silorane and Dimethacrylate Resin Based Composite Restorative Materials under Different pH Conditions
نویسندگان
چکیده
BACKGROUND The purpose of this study was to evaluate the effect of different pH solutions on the solubility and wear resistance of Silorane and dimethacrylate resin based composite restorative materials. MATERIALS AND METHODS Two different resin based restorative materials (Filtek Silorane P90 and hybrid composite Z100) were tested. Different pH solutions (2.5 and 5) also were used. A total of 60 samples of each type of selected composite were prepared. Specimens were immersed in each type of pH solutions (2.5 and 5) and distilled water as a control group for 24 h then the specimens was subjected to the required mechanical tests. RESULTS Significant statistical differences were observed regarding water solubility and wear values in different pH solutions. Filtek Silorane presented the smallest values of water solubility and wear values. CONCLUSION Under tested experimental conditions, the pH solutions used in this study showed pronounced effect on water solubility and wear values of both two restorative materials. Finally, within the limitation of this study we recommended to use Filtek Silorane (P90) instead of hybrid (Z100) due to its low solubility values under different pH solutions.
منابع مشابه
A comparative evaluation of microleakage around class V cavities restored with different tooth colored restorative materials.
OBJECTIVES To evaluate and compare microleakage around class V cavities restored with silorane and dimethacrylate-based composite resins. METHODS Standard Class V cavities were prepared on the buccal surface of 60 non-carious human molars. Teeth were randomly divided into 3 groups (n=20) depending on the restorative materials used, Silorane-based composite resin (Filtek P90-SIL), dimethacryla...
متن کاملTemperature changes under demineralized dentin during polymerization of three resin-based restorative materials using QTH and LED units
OBJECTIVES Light-curing of resin-based materials (RBMs) increases the pulp chamber temperature, with detrimental effects on the vital pulp. This in vitro study compared the temperature rise under demineralized human tooth dentin during light-curing and the degrees of conversion (DCs) of three different RBMs using quartz tungsten halogen (QTH) and light-emitting diode (LED) units (LCUs). MATER...
متن کاملThe effect of repeated preheating of dimethacrylate and silorane-based composite resins on marginal gap of class V restorations
Background. One of the problems with composite resin restorations is gap formation at resin‒tooth interface. The present study evaluated the effect of preheating cycles of silorane- and dimethacrylate-based composite resins on gap formation at the gingival margins of Class V restorations. Methods. In this in vitro study, standard Class V cavities were prepared on the buccal surfaces of 48 bovin...
متن کاملمقایسهی میزان ریزنشت حفرات کلاس II ترمیم شده با کامپوزیتهای سایلوران و متاکریلات بیس با استفاده از دوروش مختلف ترمیمی (روش ساندویچ باز، باندینگ)
Background and Objective: Polymerization shrinkage in composite resins is responsible for microleakage restoration. A recently introduced composite resin Filtek P90 is based on siloxanes and oxiranes which polymerize by cationic "ring opening" polymerization resulting in reduced polymerization shrinkage. The aim of this study was comparative evaluation of microleakage in class II cavities resto...
متن کاملSolubility of Two Resin Composites in Different Mouthrinses
AIM This study aimed to compare the solubility of a universal restorative resin composite (Filtek Z250; FZ250) and a silorane-based resin composite (Filtek Silorane; FS) after immersion in alcohol-containing mouthrinse, alcohol-free mouthrinse, and artificial saliva. METHODS 30 discs (10 mm × 1 mm) were prepared from each material and desiccated until a constant mass was obtained. Specimens w...
متن کامل