A ‘nano-battering ram’ for measuring surface forces - Obtaining force-distance curves and sidewall stiction data with a MEMS device

نویسندگان

  • W. Merlijn van Spengen
  • Elco Bakker
  • Joost W. M. Frenken
چکیده

MEMS (micro-electromechanical systems) devices often suffer from stiction induced reliability problems. Although a theoretical framework to describe stiction in MEMS is under development in the scientific community, experimental data are still scarce. We have developed a MEMS device that can be used to electronically measure sidewall surface forces in situ, i.e. on chip. To be able to use it, we have developed a sensitive electronic readout system that detects comb drive capacitance variations with 10 atto-Farad resolution. In addition, we use a model to correct the measured capacitance changes for the ground-planeinduced levitation effect of the comb drive. Our first results for the interaction between oxidized polycrystalline silicon sidewall surfaces show that at a relative humidity (RH) of 45% and a temperature of 27°C the stiction force amounts to 6.7±1.6kPa, which we assume to be mainly caused by capillary condensation. This stiction force was found to be independent of both the normal force with which the surfaces were pressed against each other prior to the stiction measurement and the age of the contact, showing that the contact is fully elastic, and capillary condensation is instantaneous on the time scale of the measurement (milliseconds to seconds). We also use the device to measure complete force-distance curves, so that these results can be compared with AFM (atomic force microscope) measurements.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

On the reliability of electrostatic NEMS/MEMS devices: Review of present knowledge on the dielectric charging and stiction failure mechanisms and novel characterization methodologies

This paper reviews the state of the art knowledge related to critical failure mechanisms in electrostatic microand nano-electromechanical systems (MEMS and NEMS) which are the dielectric charging and stiction. It describes also the recent employed nanoscale characterization techniques for these phenomena based on Kelvin probe force microscopy (KPFM) and force–distance curve measurements. The in...

متن کامل

ساخت و آزمون کارگاهی دینامومتر اتصال سه نقطه و چرخ پنجم سرعت سنج تراکتوری

For measuring draft force and drawbar power requirements for mounted implements, precise instruments such as three-point hitch dynamometers and tractor speed measurement devices are needed. In this research, a frame-type three-point hitch dynamometer was built and evaluated. Forces applied to dynamometer are measured by three separate load cells located on a frame which can be attached to tract...

متن کامل

ساخت و آزمون کارگاهی دینامومتر اتصال سه نقطه و چرخ پنجم سرعت سنج تراکتوری

For measuring draft force and drawbar power requirements for mounted implements, precise instruments such as three-point hitch dynamometers and tractor speed measurement devices are needed. In this research, a frame-type three-point hitch dynamometer was built and evaluated. Forces applied to dynamometer are measured by three separate load cells located on a frame which can be attached to tract...

متن کامل

Nanotribology and nanomechanics in nano/biotechnology.

Owing to larger surface area in micro/nanoelectromechanical systems (MEMS/NEMS), surface forces such as adhesion, friction, and meniscus and viscous drag forces become large when compared with inertial and electromagnetic forces. There is a need to develop lubricants and identify lubrication methods that are suitable for MEMS/NEMS. For BioMEMS/BioNEMS, adhesion between biological molecular laye...

متن کامل

Suppression of Stiction in MEMS

Stiction failures in microelectromechanical systems (MEMS) occur when suspended elastic members are unexpectedly pinned to their substrates. This type of device failure develops both in fabrication and during device operation, being a dominant source of yield loss in MEMS. Stiction failures require first a collapse force that brings the elastic member contact with the substrate followed by an i...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2007