Fatigue Life Assessment of 65Si7 Leaf Springs: A Comparative Study

نویسندگان

  • Vinkel Kumar Arora
  • Gian Bhushan
  • M. L. Aggarwal
چکیده

The experimental fatigue life prediction of leaf springs is a time consuming process. The engineers working in the field of leaf springs always face a challenge to formulate alternate methods of fatigue life assessment. The work presented in this paper provides alternate methods for fatigue life assessment of leaf springs. A 65Si7 light commercial vehicle leaf spring is chosen for this study. The experimental fatigue life and load rate are determined on a full scale leaf spring testing machine. Four alternate methods of fatigue life assessment have been depicted. Firstly by SAE spring design manual approach the fatigue test stroke is established and by the intersection of maximum and initial stress the fatigue life is predicted. The second method constitutes a graphical method based on modified Goodman's criteria. In the third method codes are written in FORTRAN for fatigue life assessment based on analytical technique. The fourth method consists of computer aided engineering tools. The CAD model of the leaf spring has been prepared in solid works and analyzed using ANSYS. Using CAE tools, ideal type of contact and meshing elements have been proposed. The method which provides fatigue life closer to experimental value and consumes less time is suggested.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effect of Assembly Stresses on Fatigue Life of Symmetrical 65Si7 Leaf Springs

The maximum stress induced plays vital role in fatigue life improvement of leaf springs. To reduce this maximum stress, leaves with different unassembled cambers are assembled by pulling against each other and a common curvature is established. This causes stress concentration or sets assembly stress in the assembled leaf springs which is subtractive from load stress in master leaf while it is ...

متن کامل

A Comparative Study of Standard, Casted and Riveted Eye Design of a Mono Leaf Spring Using CAE Tools

The objective of the present study is to determine better eye end design of a mono leaf spring used in light motor vehicle. A conventional 65Si7 spring steel leaf spring model with standard eye, casted and riveted eye end are considered. The CAD model of the leaf springs is prepared in CATIA and analyzed using ANSYS. The standard eye, casted and riveted eye leaf springs are subjected to similar...

متن کامل

AN INVESTIGATION ON FATIGUE AND FATIGUE CORROSION BEHAVIOR OF Cr-Si SPRING STEEL AFTER Zn-Ni ELECTROPLATING USING WEIBULL STATISTICAL MODEL

Compression springs were prepared from Cr-Si high strength spring steel and coated with pure Zn and ZnNi by electroplating process. The effect of baking after electroplating as well as applying an electroless nickel interlayer on the fatigue and fatigue corrosion of the springs was investigated. The results were analyzed using weibull statistical model. A considerable improvement (8%) in fati...

متن کامل

Assessment of the Existing Models to Estimate the Fatigue Life under both Multiaxial in Phase and 90° Out of Phase Loading Conditions

Engineers have a range of methods to estimate the fatigue life under multiaxial conditions. Each of these predictive methods is generally subjected to restrictions, related to the inherent simplified assumptions. The objective of this paper is to evaluate the validity of commonly used multiaxial fatigue criteria for different multiaxial loading conditions. The best criterion is identified throu...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 2014  شماره 

صفحات  -

تاریخ انتشار 2014